You are here: Home > Pole Line Hardware > Ground Rods & Bonding Products
We found 33 results matching your criteria.
Ground Rods & Bonding Products
Sort By:
1
12" Economy Copper Ground Strap H-2162 12" Economy Copper Ground Strap H-2162

  • Provides a permanent connection between a copper water pipe or power service mast and a #14 to #10 AWG ground wire.
  • Strap is equipped with an integral square nut which has a male engagement projection that works as a guide during assembly. Strap is supplied with a wire washer and hex nut/hex screw.
  • Hardware is sized for installation with a standard 3/8" - 7/16" Can Wrench.
  • Hardware is manufactured from pure brass.
  • Copper Ground Straps are manufactured from dead soft Copper.
  • Stock size is 1/2" x .020".
  • UL Listed.
12" Economy Copper Ground Strap H-2162

Our Price: $0.96
7/16" Strand Tap Clamp H-438ALC 7/16" Strand Tap Clamp H-438ALC

  • Used to make an electrical connection between ground wire and messenger or guy strands
  • Up to 2/0 AWG ground wire
  • Up to 7/16" strand size
  • Constructed of aluminum
7/16" Strand Tap Clamp H-438ALC

Our Price: $5.54
Allied Bolt Bronze Bonding Clamp Allied Bolt Weaver Bonding Clamp J8300

    • Used to bond #6 copper wire to 1/4" or 5/16" strand
    • Constructed of high strength copper alloy
    • Installation does not require removal of bolt
    • Semi tin plated with one bare bronze groove for copper to copper bond and other groove to be used with dissimilar metals
    • Installs with standard terminal wrench
AKA Weaver Bonding Clamp.


Our Price: $2.80
Aluminum Grounding Lug Terminal 8700 Aluminum Grounding Lug Terminal 8700

ALUMINUM GROUNDING LUG

    • Used to mechanically bond ground wire to equipment.
    • One hole on front of connector for attaching ground wire.
    • Accepts ground wire ranging from #14 - #4 AWG
    • Mounting hole accommodates 1/4" stud.
    • Body constructed from high strength Aluminum.
    • Set screw is installed with a flat head screwdriver.

Our Price: $0.36
B Strand Grounding Clamp "Mailbox Clamp" J7956 B Strand Grounding Clamp "Mailbox Clamp" J7956

This grounding clamp is used to bond the cable sheath to the messenger strand. Clamp body is made with an inside keeper riding on the end of the bolt. 1/2" bolt can be removed to place the clamp over the messenger wire.

Our Price: $2.51
Bronze Bonding Clamp 2125 UL Bronze Bonding Clamp J8301/ALL2125 UL

The semi-Tin plated Bronze Bonding Clamp assembly consists of two clamp sections and a 5/16 x 7/8-inch bronze hex washer head bolt.
One clamp section is tapped to allow installation with a single wrench.

Our Price: $4.04
Copper Ground Rod 5/8" x 10' PWC5810 Copper Ground Rod 5/8" x 10' PWC5810

Ground rods are driven vertically into the ground and bonded together with bare copper wire for electrical grounding.

Our Price: $16.99
Copper Ground Rod H PWC588 Copper Ground Rod 5/8" x 8' PWC588

  • Ground rods are driven vertically into the ground and bonded together with bare copper wire for electrical grounding.

Our Price: $13.64
Blackburn Copper Bonded Steel Ground Rod 10' Copper Ground Rod Blackburn Bonded Steel 10'

A 3/4" X 10' Copper Bonded Steel Ground Rod. All Blackburn ground rods have
a heavy uniform covering of electrolytic copper bonded to a rigid steel core.
Copper ions are forced electrically to join with the steel core, establishing a
corrosion-resistant bond between the copper and the steel.

Our Price: $26.29
Blackburn Copper Bonded Steel Ground Rod 12' Copper Ground Rod Blackburn Bonded Steel 12'

A 3/4" X 12' Copper Bonded Steel Ground Rod. All Blackburn ground rods have
a heavy uniform covering of electrolytic copper bonded to a rigid steel core.
Copper ions are forced electrically to join with the steel core, establishing a
corrosion-resistant bond between the copper and the steel.

Our Price: $44.00
Ground Rod Clamp Breakaway ACORN NUT for 5/8" and 1/2" rods Ground Rod Clamp Breakaway ACORN for 5/8" and 1/2" rods

Product Description
Ground Rod Clamps
Cast bronze, accommodates #12—1/0 AWG (unless otherwise noted).
Features
•Two diameters allow for placement before or after the ground rod has been driven. (A peened-over ground rod is passed through the larger opening and secured in the smaller diameter.) •A locking device prevents the bolt from loosening. •Bronze material keeps corrosion to a minimum.
Clamps marked UL listed, and with a ground wire range of #12–1/0 solid or stranded, are listed as suitable for direct burial and the following ground wire combinations:
Single wire - #12–#1/0 AWG Two like wires - #6, #10, #12 AWG Three like wires - #6, #10, #12 AWG
Unlike wire combinations:
Two #2 AWG with one #6 AWG One or two #10 AWG with one #12 AWG One or two #12 AWG with one #10 AWG

Our Price: $6.58
Ground Rod Clamp J8225 Ground Rod Clamp J8225

These ground rod clamps have a 7/16" U-bolt and a drop forged clamping piece.

Our Price: $7.47
Ground Rod Clamp J8491 Ground Rod Clamp J8491 1/2" ACORN NUT

Bronze Ground Rod Clamps, used with copperbonded 1/2" ground rods, provide a low resistance, secure copper-to-coppe...

Our Price: $3.09
5/8" Acorn Ground Rod Clamp J8492 Ground Rod Clamp J8492 5/8" ACORN NUT

Bronze ground rod clamp, used with copper - bonded ground rods, provide a low resistance, secure copper to copper connection.

Our Price: $2.40
Ground Rod Clamp J8493 Ground Rod Clamp J8493 3/4" ACORN NUT

Bronze Ground Rod Clamps, used with copperbonded 3/4" ground rods, provide a low resistance, secure copper-to-copper connection. These heavy-duty clamps develop a high-pressure contact between the rod and the grounding wire and can be easily disconnected when it is desired to measure resistance of the ground.

Our Price: $3.83
Ground Rod Driver pounder Lemco H693 Ground Rod Driver Lemco H-693

Sliding hammer type ground rod driver provides maximum operator safety and driving force.

Our Price: $274.44
GROUND ROD DRIVER SOCKET SDS MAX SHANK 3/4" GROUND ROD DRIVER SOCKET SDS MAX SHANK 3/4"

SDS MAX DRIVE: Only Fits SDS Max Drills.
9-3/4" Ground Rod Driver FOR 5/8 OR 3/4" GROUND RODS
MILWAUKEE PART# 48-62-4091 JAM-RDSKT-MIL48-62-4091-GRND

Our Price: $149.33
H-COATED COPPER WIRE #6 GROUND WIRE COPPER WIRE #6 H-COATED SOLID

#6 guage poly ASTMB3 coated solid copper wire 500 ft. Priced per roll. Black coating

Our Price: $345.50
Copper Wire #6 Solid  315ft GROUND WIRE Copper Wire #6 Solid 315 FT

Soft # 6 bare copper wire 315 ft
Priced per roll

Our Price: $164.00
H-J27276 5/8 GROUND CLAMP H-J27276 5/8 GROUND CLAMP

H-J27276 5/8 GROUND CLAMP

Features:
MacLean galvanized steel bond clamps provide a sturdy and efficient provision to connect ground wire to threaded bolts. The clamps are designed to nest over the square nut of the bolt. The grounding connection is accomplished by inserting the ground wire between the nut and the bonding clamp and adding an additional nut to secure the clamp and ground connection. The clamps accommodate the most common range of ground wire diameters

Our Price: $1.76
H-J27277 3/4 GROUND CLAMP H-J27277 3/4 GROUND CLAMP

H-J27277 3/4 GROUND CLAMP

Features:
MacLean galvanized steel bond clamps provide a sturdy and efficient provision to connect ground wire to threaded bolts. The clamps are designed to nest over the square nut of the bolt. The grounding connection is accomplished by inserting the ground wire between the nut and the bonding clamp and adding an additional nut to secure the clamp and ground connection. The clamps accommodate the most common range of ground wire diameters

Our Price: $2.05
LEMCO GROUND ROD CAP LEMH-207 LEMCO H-207 GROUND ROD CAP LEM207

LEMCO GROUND ROD CAP LEMH-207.
Drive ground rods safely with the Lemco Ground Rod Cap. The 2" diameter surface provides a better target for hammer power, reducing personal injuries due to hammer deflection. Increases speed while protecting ground rods against distortion and damage to finish. Solid steel, plated. Wt. 3 lbs.

Our Price: $22.12
Pipe GroundCLAMP/BRONZE H-965 Pipe Ground CLAMP/BRONZE H-965

J hooks are used for supporting bail-type drop wire and deadend clamps from poles and crossarms.

Our Price: $1.90
Split Bolt Allied 852 S-2 Copper Split Bolt S-2 Copper H-852/SI 2002

  • Larger Split Bolt
  • Used to make a bonding connection between two copper ground wires.
  • Bolt and nut formed from high-strength corrosion resistant C210 Copper.
  • Specially designed pressure bar provides high pull-out strength.
  • Under torque, provides high contact pressure between ground wires.
  • Smallest two conductors accepted: 6 Sol.
  • Largest two conductors accepted: 2 Str.
  • Min. wire size that can be used with Max. wire size: 14 Str.
  • Tested and UL listed to UL486A requirements.

Our Price: $1.59
Allied Bolt 853 Split Bolt S-4 Copper Split Bolt S-4 Copper H-853/SI 2004

  • Used to make a bonding connection between two copper ground wires.
  • Bolt and nut formed from high-strength corrosion resistant C210 Copper.
  • Specially designed pressure bar provides high pull-out strength.
  • Under torque, provides high contact pressure between ground wires.
  • Smallest two conductors accepted: 8 Sol.
  • Largest two conductors accepted: 4 Sol.
  • Min. wire size that can be used with Max. wire size: 16 Sol.
  • Tested and UL listed to UL486A requirements.

Our Price: $1.86
H-854--SI-2006-SPLIT-BOLT Split Bolt S-6 Copper H-854/SI 2006

H-854 /SI-2006 SPLIT BOLT
Allied Bolt Part # 854

  • Used to make a bonding connection between two copper ground wires.
  • Bolt and nut formed from high-strength corrosion resistant C210 Copper.
  • Specially designed pressure bar provides high pull-out strength.
  • Under torque, provides high contact pressure between ground wires.
  • Smallest two conductors accepted: 10 Sol.
  • Largest two conductors accepted: 6 Sol.
  • Min. wire size that can be used with Max. wire size: 16 Sol.
  • Tested and UL listed to UL486A requirements.

Our Price: $0.76
Tiiger Ground Rod 3/4 Driver Tiiger Ground Rod 3/4 Driver

The Tiiger ground rod driver eliminates the need to climb above the rod for installation.
Designed with a positioning guide pin which allows the driver socket of the impact tool to
be engaged to the ground rod driver.

Our Price: $72.95
Tiiger Ground Rod 5/8 Driver Tiiger Ground Rod 5/8 Driver

The Tiiger ground rod driver eliminates the need to climb above the rod for installation. Designed with a positioning guide pin which allows the driver socket of the impact tool to be engaged to the ground rod driver.

Our Price: $68.95
HUB GC-164 BRONZE VISE TYPE BONDING CONNECTOR VISE TYPE BONDING CONNECTOR HUB GC-164 BRONZE

For connecting ribbon or braid to ribbon, braid or bus.
Side Opening Jaw facilitates easy installation.

Run Conductor Size and Type Cu ribbon 1/4", Cu braid 1/4"
Tap Conductor Size and Type Cu 6 sol, Cu 6 str (7), Cu ribbon 1/4", Cu braid 1/4"

Our Price: $4.61
5/16 Bolt  Vise Type C Clamp Connectors H-BVC-167P Vise Type C Clamp Connector Bolt H-BVC-167P

Designed specifically for connecting a ground wire to a figure 8 messenger strand, where self-supporting cable is used
accommodates messenger diameters of .146" to .312".
Constructed of tin-plated bronze
5/16 - 24 bolt size, 9/16" hex
Messenger Grounding Connector

C Ground Connector accommodates ground conductors
ranging from #8 STR AWG to #4 STR AWG.

Our Price: $4.31
Vise Type Clamp Connectors EM-0167/S Vise Type Clamp Connectors EM-0167/S

Silicon bronze clamps adjustable by single hex head screws, used to connect various size grounding conductors, as well as pole line apparatus to grounding conductors. Features.Casting and bolt are both made of silicon bronze for greater strength, conductivity, and corrosion resistance. Install using the standard can wrench. EM 0167 Tin-plated bronze C connector with teeth for piercing the messenger insulation of Figure 8 cable. For messenger diameters of .146"–.312" (3.71–7.94mm) and ground conductor range of .146"–.312". Available with stainless steel or bronze bolt.

Our Price: $5.40
Vise Type Clamp Connectors EM-2370 Bronze Vise Type Clamp Connectors EM-2370 Bronze

Silicon bronze clamps adjustable by single hex head screws, used to connect various size grounding conductors, as well as pole line apparatus to grounding conductors. Features.Casting and bolt are both made of silicon bronze for greater strength, conductivity, and corrosion resistance. Install using the standard can wrench. EM 2370 Manufactured to Bell Spec CA08980 (H1). It accommodates: •Single or multiple #6 AWG wires solid or stranded. •#6 AWG to #10 or #12 AWG. •From single 2-pair BSW metallic shield, to three 2-pair BSW metallic shields.

Our Price: $3.11
Vise Type Clamp Connectors EM-2372/S Bronze Vise Type Clamp Connectors EM-2372/S Bronze

Silicon bronze clamps adjustable by single hex head screws, used to connect various size grounding conductors, as well as pole line apparatus to grounding conductors.
Features.Casting and bolt are both made of silicon bronze for greater strength, conductivity, and corrosion resistance. Install using the standard can wrench.

H2 silicon bronze clamp.

Accommodates:

•#12–#4 AWG solid.
•1/0 B, C, or D stranded copper to #6, #8, #10, #12 AWG solid bare copper wire.
•6.6–10M support strand to #6, #8, #10, #12 AWG solid bare copper wire.
Add suffix -T for a tin-plated clamp.

Our Price: $2.99
   
 
1