You are here: Home > Pole Line Hardware > Anchors and Rods
We found 77 results matching your criteria.
ANCHOR RODS (PISA) CROSS PLATE ANCHORS EXPANDING ANCHORS (BUST)
MANTA RAY ANCHORS NO WRENCH SCREW ANCHORS POWER DRIVE ANCHORS
ROCK ANCHORS THIMBLE EYE ANCHOR RODS Auxiliary Eyes
Anchors and Rods
Sort By:
1 2
MSI-D10426 10" SOLID SQUARE HUB TWIN HELIX POWER DRIVEN ANCHOR 1-3/8" HUB - 6000 FT. LB. FOR 3/4" AND 1" RODS *10" SOLID SQUARE HUB TWIN HELIX POWER DRIVEN ANCHOR 1-3/8" HUB - 6000 FT. LB. FOR 3/4" AND 1" RODS H-D10426-HUB1021637

  • Installation is performed using a power digger. An anchor wrench fits over the square hub and a torque measurement device is required to determine proper installation.
  • Correct installation is achieved only when the anchor is installed using the appropriate torque for the particular soil and anchor type.
  • Installation torque is usually measured using a device connected in series with the wrench, digger, and Kelley Bar during installation.

Our Price: $144.20
MACLEAN D2104 10" TWIN SOLID SQUARE HUB HELIX POWER DRIVEN ANCHOR 1-1/2" HUB - 6000 FT. LB. FOR 3/4" AND 1" RODS MACLEAN D2104 *10" TWIN SOLID SQUARE HUB HELIX POWER DRIVEN ANCHOR 1-1/2" HUB - 6000 FT. LB. FOR 3/4" AND 1" RODS H-D2104

  • Installation is performed using a power digger. An anchor wrench fits over the square hub and a torque measurement device is required to determine proper installation.
  • Correct installation is achieved only when the anchor is installed using the appropriate torque for the particular soil and anchor type.
  • Installation torque is usually measured using a device connected in series with the wrench, digger, and Kelley Bar during installation.

Our Price: $148.80
ALLIED BOLT 492 4" TWIN SOLID SQUARE HUB HELIX POWER DRIVEN ANCHOR 1-3/8" HUB - 6000 FT. LB. FOR 3/4" AND 1" RODS *4" TWIN SOLID SQUARE HUB HELIX POWER DRIVEN ANCHOR 1-3/8" HUB - 6000 FT. LB. FOR 3/4" AND 1" RODS H-492

  • Installation is performed using a power digger. An anchor wrench fits over the square hub and a torque measurement device is required to determine proper installation.
  • Correct installation is achieved only when the anchor is installed using the appropriate torque for the particular soil and anchor type.
  • Installation torque is usually measured using a device connected in series with the wrench, digger, and Kelley Bar during installation.

Our Price: $91.73
SALE Price: $75.62
You save $16.11!
*1-1/2" TWIN SQUARE HUB ANCHOR – 7000 FT-LB INSTALLATION TORQUE D2847 *8" TWIN SOLID SQUARE HUB HELIX POWER DRIVEN ANCHOR 1-1/2" HUB - 7000 FT. LB. FOR 3/4" AND 1" RODS H-D2847

  • Installation is performed using a power digger. An anchor wrench fits over the square hub and a torque measurement device is required to determine proper installation.
  • Correct installation is achieved only when the anchor is installed using the appropriate torque for the particular soil and anchor type.
  • Installation torque is usually measured using a device connected in series with the wrench, digger, and Kelley Bar during installation.

Our Price: $135.47
MSI D10426  8" TWIN SOLID SQUARE HUB HELIX POWER DRIVEN ANCHOR 1-3/8" HUB - 6000 FT. LB. FOR 3/4" AND 1" RODS *8" TWIN SOLID SQUARE HUB HELIX POWER DRIVEN ANCHOR 1-3/8" HUB - 6000 FT. LB. FOR 3/4" AND 1" RODS D8426-HUB1021636

  • Installation is performed using a power digger. An anchor wrench fits over the square hub and a torque measurement device is required to determine proper installation.
  • Correct installation is achieved only when the anchor is installed using the appropriate torque for the particular soil and anchor type.
  • Installation torque is usually measured using a device connected in series with the wrench, digger, and Kelley Bar during installation.

Our Price: $126.19
SALE Price: $98.14
You save $28.05!
2-1/2" SOCKET ANCHOR 8" 8000 FT. LB. FOR 3/4" AND 1" RODS  Allied Bolt 3521 `2-1/2" SOCKET ANCHOR 8" 8000 FT. LB. FOR 3/4" AND 1" RODS Allied Bolt 3521

2-21/2" SOCKET ANCHOR 8" 8000 FT. LB. FOR 3/4" AND 1" RODS Allied Bolt 3521.

  • Installation is performed using a drive wrench which fits into the anchor hub.
  • Proper anchor selection depends on the type of soil and guying requirements.
  • The Anchors have a 3" helix pitch.
  • Installation uses standard tools.
  • Anchors are painted with rust inhibiting blue paint after fabrication.

*To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only.

Our Price: $83.43
SALE Price: $73.00
You save $10.43!
2-1/4" SOCKET ANCHOR 8"  10000 FT. LB. FOR 3/4" AND 1" RODS Allied Bolt 3511 `2-1/4" SOCKET ANCHOR 8" 10000 FT. LB. FOR 3/4" AND 1" RODS Allied Bolt 3511

2-1/4" SOCKET ANCHOR 8" 10000 FT. LB. FOR 3/4" AND 1" RODS Allied Bolt 3511.

  • Installation is performed using a drive wrench which fits into the anchor hub.
  • Proper anchor selection depends on the type of soil and guying requirements.
  • The Anchors have a 3" helix pitch.
  • Installation uses standard tools.
  • Anchors are painted with rust inhibiting blue paint after fabrication.

To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only.

Our Price: $76.64
SALE Price: $63.12
You save $13.52!
2-1/4" SOCKET ANCHOR 8" 8000 FT. LB. FOR 3/4" AND 1" RODS Allied Bolt 3501 `2-1/4" SOCKET ANCHOR 8" 8000 FT. LB. FOR 3/4" AND 1" RODS Allied Bolt 3501

2-1/4" SOCKET ANCHOR 8" 8000 FT. LB. FOR 3/4" AND 1" RODS Allied Bolt 3501.

  • Installation is performed using a drive wrench which fits into the anchor hub.
  • Proper anchor selection depends on the type of soil and guying requirements.
  • The Anchors have a 3" helix pitch.
  • Installation uses standard tools.
  • Anchors are painted with rust inhibiting blue paint after fabrication.

To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only.

Our Price: $76.64
SALE Price: $63.12
You save $13.52!
1-1/2” SINGLE SOLID SQUARE HUB ANCHOR 10" HELIX POWER HUB ANCHOR – 7000 FT-LB INSTALLATION TORQUE H-D1104-7 1-1/2” SQUARE HUB ANCHOR – 7,000 FT-LB 10" INSTALLATION TORQUE H-D1104-7

1-1/2” SINGLE SOLID SQUARE HUB ANCHOR 10" HELIX POWER HUB ANCHOR – 7000 FT-LB

  • Installation is performed using a power digger. An anchor wrench fits over the square hub and a torque measurement device is required to determine proper installation.
  • Correct installation is achieved only when the anchor is installed using the appropriate torque for the particular soil and anchor type (see reference charts).
  • Proper anchor selection depends on the type of soil and guying requirements.
  • Installation torque is usually measured using a device connected in series with the wrench, digger, and Kelly Bar during installation.
*To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only.

Our Price: $73.57
1-1/2" SINGLE SOLID SQUARE HUB ANCHOR 10" HELIX POWER HUB ANCHOR – 8000 FT-LB 1-1/2” SQUARE HUB ANCHOR 10" 8000 FT-LB INSTALLATION TORQUE H-D1104-8/Allied

1-1/2" SINGLE SOLID SQUARE HUB ANCHOR 10" HELIX POWER HUB ANCHOR – 8000 FT-LB

  • Installation is performed using a power digger. An anchor wrench fits over the square hub and a torque measurement device is required to determine proper installation.
  • Correct installation is achieved only when the anchor is installed using the appropriate torque for the particular soil and anchor type (see reference charts).
  • Proper anchor selection depends on the type of soil and guying requirements.
  • Installation torque is usually measured using a device connected in series with the wrench, digger, and Kelly Bar during installation.
*
To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only.

Our Price: $73.57
1-1/2” SINGLE SOLID SQUARE HUB ANCHOR – 5,500 FT-LB INSTALLATION TORQUE 1-1/2” SQUARE HUB ANCHOR 14" 5,500 FT-LB INSTALLATION TORQUE H-D1134

1-1/2” SINGLE SOLID SQUARE HUB ANCHOR 14" HELIX POWER HUB ANCHOR – 5,500 FT-LB

  • Installation is performed using a power digger. An anchor wrench fits over the square hub and a torque measurement device is required to determine proper installation.
  • Correct installation is achieved only when the anchor is installed using the appropriate torque for the particular soil and anchor type (see reference charts).
  • Proper anchor selection depends on the type of soil and guying requirements.
  • Installation torque is usually measured using a device connected in series with the wrench, digger, and Kelly Bar during installation.
*To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only.

Our Price: $119.97
SALE Price: $93.31
You save $26.66!
1-1/2" SINGLE SOLID SQUARE HUB ANCHOR 8" HELIX POWER HUB ANCHOR – 7000 FT-LB INSTALATION TORQUE H-D184-7 1-1/2” SQUARE HUB ANCHOR 8" 7,000 FT-LB INSTALLATION TORQUE H-D184-7

1-1/2" SINGLE SOLID SQUARE HUB ANCHOR 8" HELIX POWER HUB ANCHOR – 7000 FT-LB

  • Installation is performed using a power digger. An anchor wrench fits over the square hub and a torque measurement device is required to determine proper installation.
  • Correct installation is achieved only when the anchor is installed using the appropriate torque for the particular soil and anchor type (see reference charts).
  • Proper anchor selection depends on the type of soil and guying requirements.
  • Installation torque is usually measured using a device connected in series with the wrench, digger, and Kelly Bar during installation.
*To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only.

Our Price: $59.74
1-3/8” SQUARE HUB ANCHORS – 6,000 FT-LB. INSTALLATION TORQUE H-D84-6 1-3/8” SQUARE HUB ANCHORS 8" 6,000 FT-LB. INSTALLATION TORQUE H-D84-6

1-3/8” SQUARE HUB ANCHORS – 6,000 FT-LB. INSTALLATION TORQUE

  • Installation is performed using a power digger. An anchor wrench fits over the square hub and a torque measurement device is required to determine proper installation.
  • Correct installation is achieved only when the anchor is installed using the appropriate torque for the particular soil and anchor type (see reference charts).
  • Proper anchor selection depends on the type of soil and guying requirements.
  • Installation torque is usually measured using a device connected in series with the wrench, digger, and Kelly Bar during installation.
*To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only.

Our Price: $55.31
SALE Price: $43.02
You save $12.29!
Expanding Anchor For 1" Rod J8200-1 10" Expanding Anchor For 1" Rod J8200-1

Expanding anchors are made for installation in holes augered by power drills. One piece formed anchor with wings and a base. A retainer on the bottom holds the nut from the forged eye rod. The Expanding Anchor is 10" wide and is for a 1" double or triple eye rod Only.

Our Price: $75.71
10" Expanding Anchor For 5/8" or 3/4" Rod J8200-3/4/ALL19023 10" Expanding Anchor For 5/8" or 3/4" Rod J8200-3/4/ALL19023

H-J8200-3/4/ALL19023 Burst Anchor Rod

  • Hole Size: 10"
  • Area (Sq. In.): 200
  • Rod Size: 5/8" & 3/4"
  • Made for installation in holes augered by power driller
  • One-piece formed anchors with wings and a base
  • Retainer on the bottom holds the nut from the forged eye nut from the forged eye rod

Our Price: $75.71
Expanding Bust Plate Anchor 12" Expanding Anchor For 1" Rod J0283-1

Expanding anchors are made for installation in holes augered by power drills. One piece formed anchor with wings and a base. A retainer on the bottom holds the nut from the forged eye rod. The Expanding Anchor is 12" wide and is for a 1" double or triple eye rod Only.

Our Price: $126.69
J0283 12" Expanding Anchor For 1-1/4" Rod 12" Expanding Anchor For 1-1/4" Rod J0283

Expanding anchors are made for installation in holes augered by power drills. One piece formed anchor with wings and a base. A retainer on the bottom holds the nut from the forged eye rod. The Expanding Anchor is 12" wide and is for a 1 1/4" double or triple eye rod Only.

Our Price: $126.69
2-1/2” TURBO DRIVE SOCKET ANCHOR 10" HELIX POWER HUB ANCHOR – 15,000 FT-LB FOR 3/4" AND 1" RODS H-TD250-104 2-1/2” TURBO DRIVE SOCKET ANCHOR 10" HELIX POWER HUB ANCHOR – 15,000 FT-LB FOR 3/4" AND 1" RODS H-TD250-104

2-1/2” TURBO DRIVE SOCKET ANCHOR 10" HELIX POWER HUB ANCHOR – 15,000 FT-LB FOR 3/4" AND 1" RODS

  • Installation is performed using a drive wrench which fits into the anchor hub.
  • Proper anchor selection depends on the type of soil and guying requirements.

*To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only..

Our Price: $100.59
2-1/4" TURBO DRIVE SOCKET ANCHOR 10" HELIX POWER HUB ANCHOR – 10,000 FT-LB FOR 3/4" AND 1" RODS H-TD225-104 2-1/4" TURBO DRIVE SOCKET ANCHOR 10" HELIX POWER HUB ANCHOR – 10,000 FT-LB FOR 3/4" AND 1" H-TD225-104

2-1/4" TURBO DRIVE SOCKET ANCHOR 10" HELIX POWER HUB ANCHOR – 10,000 FT-LB FOR 3/4" AND 1" RODS

  • Installation is performed using a drive wrench which fits into the anchor hub.
  • Proper anchor selection depends on the type of soil and guying requirements.

*To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only.

Our Price: $78.80
2-1/4" TURBO DRIVE SOCKET ANCHOR – 10,000 FT-LB FOR 3/4" AND 1" RODS H-TD225-84/ALL3511 2-1/4" TURBO DRIVE SOCKET ANCHOR 8" HELIX POWER HUB ANCHOR – 10,000 FT-LB FOR 3/4" AND 1" RODS H-TD225-84/ALL3511

2-1/4" TURBO DRIVE SOCKET ANCHOR – 10,000 FT-LBFOR 3/4" AND 1" RODS – 3/8" THICK HELIX

  • Installation is performed using a drive wrench which fits into the anchor hub.
  • Proper anchor selection depends on the type of soil and guying requirements.

*To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only.

Our Price: $76.64
SALE Price: $61.88
You save $14.76!
6" Expanding Anchor For 1/2" or 5/8" Rod J0870 6" Expanding Anchor For 1/2" or 5/8" Rod J0870

H-J0870 Bust Anchor Expanding 6"

  • Hole Size: 6"
  • Area (Sq. In.): 70"
  • Rod Size: 5/8"
  • Made for installation in holes augered by power drillers
  • One piece formed anchors with wing and a base
  • Retainer on the bottom holds the nut from the forged eye rod

Our Price: $29.01
Expanding Anchor J8135-1 8" Expanding Anchor For 1" Rod J8135-1

Expanding anchors are made for installation in holes augered by power drills. One piece formed anchor with wings and a base. A retainer on the bottom holds the nut from the forged eye rod. The Expanding Anchor is 8" wide and will fit a 1" double or triple eye rod Only.

Our Price: $61.33
Expanding Anchor J8135 8" Expanding Anchor For 5/8" or 3/4" Rod J8135

Expanding anchors are made for installation in holes augered by power drills. One piece formed anchor with wings and a base. A retainer on the bottom holds the nut from the forged eye rod. The Expanding Anchor is 8" wide and will fit a 5/8" or 3/4" double or triple eye rod Only.

Our Price: $56.93
Anchor, Tool, Shear Pins-50lbs Hubbell C3030045/S Anchor, Tool, Shear Pins-50lbs Hubbell C3030045

HUBBELL C3030045/S Shear Pin 50lbs (SURPLUS)
Pin for Shear Torque Indicator. Sold Each

To be use with PISA® Anchor Rod 1" X 7' D100 PISA® Anchor Rod 1" x 3' 1/2" or PISA® Anchor Rod 3/4" x 7' D75 Only.

Our Price: $1.03
2-1/4" SOCKET ANCHOR 10" 8000 FT. LB. FOR 3/4" AND 1" RODS Hubbell C1025205 Anchor, Tough One, 10in, 8,000 ft-lb rating, 2.25in hub,1in threads Hubbell C1025205

2-1/4" SOCKET ANCHOR 10" 8000 FT. LB. FOR 3/4" AND 1" RODS

Tough One Anchor Helix, 8,000 Ft Lbs (10,848 N-M), 10" (254 mm) Helix for use with 0.75" (19.1 mm) or 1" (25.4 mm) Rod.

  • Installed with Chance anchor wrench C1021583
  • The anchor's sloped lead point improves penetration and helps soil flow from below the hub to above the anchor.
  • 1" threads to fit 3/4" and 1" diameter Pisa rod
  • Anchors are painted with a black paint

Our Price: $80.14
8" SOCKET ANCHOR 8000 FT. LB. FOR 3/4" AND 1" RODS Hubbell C1025204 Anchor, Tough One, 8in, 8,000 ft-lb rating, 2.25in hub,1in threads Hubbell C1025204

2-1/4" SOCKET ANCHOR 8" 8000 FT. LB. FOR 3/4" AND 1" RODS

Tough One Anchor Helix, 8,000 Ft Lbs (10,848 N-M), 8" (203 mm) Helix for use with 0.75" (19.1 mm) or 1" (25.4 mm) Rod.

  • Installed with Chance anchor wrench C1021583
  • The anchor's sloped lead point improves penetration and helps soil flow from below the hub to above the anchor.
  • 1" threads to fit 3/4" and 1" diameter Pisa rod
  • Anchors are painted with a black paint

Our Price: $76.64
SALE Price: $61.88
You save $14.76!
H-PA155A/ALL AUXILIARY EYE ANCHOR AUXILIARY ANCHOR EYE 1-1/4" ROD H-AE155B

FOR-1.25 Rod Auxiliary eye anchor rod clamps permit an efficient method of adding an eye to an existing anchor rod for attaching an additional guy wire 1-1/8" THIMBLE 9/16 STRAND

Our Price: $26.86
H-JAE155A AUXILIARY ANCHOR EYE 3/4-1" ROD AUXILIARY ANCHOR EYE 3/4-1" ROD H-AE155A

3/4-1" ROD Auxiliary eye anchor rod clamps permit an efficient method of adding an eye to an existing anchor rod for ataching an additional guy wire. Rating 18,000 lbs 1-1/2" THIMBLE 1/2" STRAND

Our Price: $26.34
H-PA155/S AUXILLARY EYE ANCHOR AUXILLARY ANCHOR EYE 5/8-3/4 Rod H-AE155

5/8" to "3/4" ROD
Auxiliary eye anchor rod clamps permit an efficient method of adding an eye to an existing anchor rod for attaching an additional guy wire 1-1/2" THIMBLE 1/2" STRAND

Our Price: $14.81
MSI J3524-1 Cross Plate Anchor 1 1/4" x 24" Cross Plate Anchor 1 1/4" x 24" J3524-1

J3524-1 24" with the 1-1/4 rod Cross Plate anchors are made for made for installation in holes augered by power drillers. One piece plate anchor formed of two structural members that are ribbed for reinforcement. A retainer on the bottom holds the nut from the forged eye rod. The Cross Plate Anchor is 24" wide and will fit a 1 1/4" double or triple eye rod Only.

Our Price: $217.26
Cross Plate Anchor J3520-1 Cross Plate Anchor 1" x 20" J3520-1

Cross Plate anchors are made for made for installation in holes augered by power drillers. One piece plate anchor formed of two structural members that are ribbed for reinforcement. A retainer on the bottom holds the nut from the forged eye rod. The Cross Plate Anchor is 20" wide and will fit a 1" double or triple eye rod Only.

Our Price: $92.84
Cross Plate Anchor 1" x 24" J3524 Cross Plate Anchor 1" x 24" J3524

Cross Plate anchors are made for made for installation in holes augered by power drillers. One piece plate anchor formed of two structural members that are ribbed for reinforcement. A retainer on the bottom holds the nut from the forged eye rod. The Cross Plate Anchor is 24" wide and will fit a 1" double or triple eye rod Only.

Our Price: $208.63
Cross Plate Anchor 3/4 x 16" J3516 Cross Plate Anchor 3/4 x 16" J3516

Cross Plate anchors are made for made for installation in holes augered by power drillers. One piece plate anchor formed of two structural members that are ribbed for reinforcement. A retainer on the bottom holds the nut from the forged eye rod. The Cross Plate Anchor is 16" wide and will fit a 3/4" double or triple eye rod Only.

Our Price: $70.07
Double Eye Anchor Rod 3/4 x 7' J7527 Double Eye Anchor Rod 3/4 x 7' J7527

3/4" X 7' Double Strand Anchor Rod 23,000 lbs Minimum Tensile Strength

  • Used for guying utility poles.
  • Used with all types of expanding anchors.
  • Contoured to prevent damage to strand.
  • Rods are threaded 3-1/2" and are assembled with a heavy square nut
  • 23,000 Lbs. ultimate strength rating
  • Hot Dip Galvanized

Our Price: $45.86
SALE Price: $35.67
You save $10.19!
Double Eye Anchor Rod 3/4 x 8' J7528/ALL4170 Double Eye Anchor Rod 3/4 x 8' J7528/ALL4170

3/4" X 8' Double Strand Anchor Rod 23,000 lbs Minimum Tensile Strength

  • Used for guying utility poles.
  • Used with all types of expanding anchors.
  • Contoured to prevent damage to strand.
  • 3-1/2" minimum thread length on all rods.
  • Minimum tensile strength is 23,000 lbs.
  • A heavy square nut is attached to every anchor rod.
  • Hot dip galvanized

Our Price: $41.34
EXPANDING ANCHOR TOOL HUB C3020003 EXPANDING ANCHOR TOOL HUB C3020003 10ft

The Chance fiberglass handle Expanding and Tamping Bar simplifies the job of expanding anchors. The curved Expander and Tamper Head distributes the weight of the bar evenly around the anchor rod to reduce handle vibration. The hook of the Expanding and Tamping Bar wraps around the anchor rod to keep the expanding head from slipping off the anchor top plate. This tool is also effectively used for tamping in soil above the installed anchor. The base casting is attached directly to the fiberglass handle.

This is 10 ft long and will ship LTL freight.

C3020003 Expanding & Tamping Bar 10'

Our Price: $906.49
Little Beaver 9051-GHLB Adaptor with 7/8" Square Drive for Groundhog Augers MANTA 9051-GHLB Little Beaver Adaptor with 7/8" Square Drive for Groundhog Augers

This adaptor adapts Little Beaver earth drills to Groundhog brands of augers. Features a 7/8" square drive connection.

Earth Drills

Our Price: $113.50
Little Beaver 30272 Adaptor, with Hardware, Keyed Shaft to Auger MANTA LB 30272 Little Beaver Adaptor Keyed Shaft to Auger w/Hardware for Groundhog Augers

Little Beaver Adaptor, with Hardware, Keyed Shft to Auger


Earth Drills

Our Price: $96.75
MANTA LB-30322 Little Beaver Utility Anchor Adaptor (Fits into #30272) MANTA LB-30322 Little Beaver Utility Anchor Adaptor (Fits into #30272)

Driving utility anchors is made easier with this special adaptor. With Little Beaver’s anchor handle, hydraulic earth drill and torque tube, one-man installation of utility anchors is now possible. (60 RPM only)

Our Price: $120.00
Manta Ray Anchor Tags Manta Ray Anchor Tags

Manta Ray  Anchor Tags

Our Price: $3.01
Manta Ray Anchor MR1 H-20036-UT-II Manta Ray Anchor MR1 H-20036-UT-II

*MR1* 7" x 14 1/2" 40,000 lbs (178 Kn) Ultimate Strength Anchor – To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only.Working loads (2-1 safety factor) 20,000 lbs (89Kn). This is anchor is hot dipped galvanized and designed to be used in normal/medium soils. It accepts anchor rods .1″ threads D100 Rod This anchor is several inches wider than the MR2

Our Price: $125.29
Manta Ray Anchor MR2 20199-UT-II-MR2 Manta Ray Anchor MR2 20199-UT-II-MR2

*MR2* 20199-UT-II-MR2 4" x 14 1/2" 40,000 lbs Manta Ray Anchor(178 Kn) Ultimate Strength Anchor –To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only. Working loads (2-1 safety factor) 20,000 lbs (89Kn). This anchor is hot dipped galvanized and designed to be used exclusively in hard/dense/cobble soils. It accepts anchor rods w/ 1.0″ threads (25 mm D100 Rod

Our Price: $111.06
Manta Ray Anchor MR3 H-20210-UT-II MR-3 Manta Ray Anchor MR3 H-20210-UT-II MR-3

20,000 lbs (89 Kn) Utilimate Strength Anchor – 7" x 14 1/2" Working loads (2-1 safety factor) 10,000 lbs (45 Kn). It is hot dipped galvanized and designed to be used for medium loads in normal/hard soils. Use with D62 5/8 Pisa Rod and J6516 5/8 twin eyenut dim:3.5x11.88 For 5/8 anchor rods only Very Similar in size to the MR2 but uses smaller 5/8 D62 Rod
Use for D-62 Rod only These will screw onto 5/8 hardware but fits too loose to be used safely for 5/8 hardware or 5/8 threaded Rod



Our Price: $77.20
Manta Ray Anchor MR3 H-20210-UT-II MR-3 Manta Ray Anchor MR4 H-20221-UT-II MR-4 Smallest

20,000 lbs (89 Kn) Utilimate Strength Anchor – 2.5" x 8.5" Working loads (2-1 safety factor) 10,000 lbs (45 Kn). It is hot dipped galvanized and designed to be used for medium loads in normal/hard soils.. Use with D62 5/8 Pisa Rod Only and J6516 5/8" twin eyenut dim:3.5x11.88 For 5/8 anchor rods only. This is the smallest of the 5 Manta Ray anchors
Use for D-62 Rod only These will screw onto 5/8 hardware but fits too loose to be used safely for 5/8 hardware or 5/8 threaded Rod



Our Price: $76.94
Manta Ray Anchor MRSR 20229-UT-II Manta Ray Anchor MRSR 20229-UT-II

To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only.
Largest Manta Ray at 17.25 x 12.5"
36,000 lbs Ultimate Strength Anchor – Working loads (2-1 safety factor) 20,000 lbs (89Kn). This is anchor is hot dipped galvanized and designed to be used in normal/medium soils. It accepts anchor rods .D-75″ or D100 rods to 1.0″ (25 mm) threads

Our Price: $201.30
SALE Price: $156.57
You save $44.73!
No-Wrench Screw Anchor 1 1/4" X 66" J6530WCA No Wrench Screw Anchor 1 1/4" X 66" With 10" Helix J6530WCA

Used for guying wires at utility poles. Anchors are installed by simply turning anchor into ground. No Wrench Anchors may be driven by hand or with power equipment. Eye dimensions are the same as Anchor Rods. Screw anchors consist of an unthreaded triple eye rod with an angled point, and a firmly welded helix. Insert No - Wrench anchor into drive head tool and secure. Helix is 1/4" thick. Hot dip galvanized to meet ASTM Specification A153, Class C. Helix anchor, twist anchor, screw anchor.

Our Price: $118.50
SALE Price: $92.17
You save $26.33!
No-Wrench Screw Anchor 1" X 66" J6528WCA No Wrench Screw Anchor 1" X 66" With 8" Helix J6528WCA

Used for guying wires at utility poles. Anchors are installed by simply turning anchor into ground. No Wrench Anchors may be driven by hand or with power equipment. Eye dimensions are the same as Anchor Rods. Screw anchors consist of an unthreaded triple eye rod with an angled point, and a firmly welded helix. 8" - Wrench anchor into drive head tool and secure. Helix is 1/4" thick. Hot dip galvanized to meet ASTM Specification A153, Class C. helix anchor, twist anchor, screw anchor.

Our Price: $72.71
No Wrench Screw Anchor 1.25X96" J6550WCA No Wrench Screw Anchor 1.25" X 96" With 10" Helix J6550WCA

Used for guying wires at utility poles. Anchors are installed by simply turning anchor into ground. No Wrench Anchors may be driven by hand or with power equipment. Eye dimensions are the same as Anchor Rods. Screw anchors consist of an unthreaded triple eye rod with an angled point, and a firmly welded helix. 10" - Wrench anchor into drive head tool and secure. Helix is 1/4" thick. Hot dip galvanized to meet ASTM Specification A153, Class C. helix anchor, twist anchor, screw anchor.

Our Price: $142.27
No Wrench Screw Anchor 3/4" X 66" J6526WCA No Wrench Screw Anchor 3/4" X 66" With 6" Helix J6526WCA

Used for guying wires at utility poles. Anchors are installed by simply turning anchor into ground. No Wrench Anchors may be driven by hand or with power equipment. Eye dimensions are the same as Anchor Rods. Screw anchors consist of an unthreaded triple eye rod with an angled point, and a firmly welded helix. 8" - Wrench anchor into drive head tool and secure. Helix is 1/4" thick. Hot dip galvanized to meet ASTM Specification A153, Class C. helix anchor, twist anchor, screw anchor.

Our Price: $51.87
Pisa Anchor  Rod 1" X 7' H-D100 PISA® Anchor Rod 1" X 7' D100

PISA® Anchor Rod 1" X 7' 36,000lb Tensile Strenght

Chance introduced this system of utilizing the power of digging equipment to install screw anchors. The system consists of a screw anchor, anchor rod and a special installing wrench. Each anchor has a galvanized steel threaded anchor rod with an upset hex; single or twin helices and a galvanized guy wire nut which is screwed to the anchor rod end. PISA anchors can be installed in a matter of minutes.

Use with MR1 MR2MRSR Manta Ray or Power Drive Anchor Only.
Use with 1" EYENUT for-Pisa-Rod only J12585-D6567 or with 1" Thimble Eyenut J16512-ALL5095

Our Price: $59.50
SALE Price: $46.28
You save $13.22!
PISA® Anchor Rod 3/4" x 7' 12632P D75 PISA® Anchor Rod 3/4" x 7' D75

PISA® Anchor Rod 3/4" x 7' 23,000lb Tensile strength
Chance introduced this system of utilizing the power of digging equipment to install screw anchors. The system consists of a screw anchor, anchor rod and a special installing wrench. Each anchor has a galvanized steel threaded anchor rod with an upset hex; single or twin helices and a galvanized guy wire nut which is screwed to the anchor rod end. PISA anchors can be installed in a matter of minutes.

Use with MR1 MR2 Manta Ray or Power Drive Anchor Only.
Use with 1" EYENUT for-Pisa-Rod only J12585-D6567 or with 1" Thimble Eyenut J16512-ALL5095

Our Price: $36.57
SALE Price: $28.44
You save $8.13!
Pisa Anchor  Rod 1" X 7' H-D100 PISA® Anchor Rod 5/8" X 7' D62

PISA® Anchor Rod 5/8" x 7' 16,000lb Tensile strength

Chance introduced this system of utilizing the power of digging equipment to install screw anchors. Use with J-6516 Twin Eyenut. The system consists of a screw anchor, anchor rod and a special installing wrench. Each anchor has a galvanized steel threaded anchor rod with an upset hex; single or twin helices and a galvanized guy wire nut which is screwed to the anchor rod end. PISA anchors can be installed in a matter of minutes. THREAD .695-11UNS-2A D62 Pisa Rod

Use with MR3 MR4 Manta Ray
Use with 5/8" Thimble Eyenut 5049 or with 5/8" Thimble Eyenut J16516-ALL5046

Our Price: $33.09
SALE Price: $25.73
You save $7.36!
Power Hub Screw Anchor Rod 1" Coupler "PISA" D354 Power Hub Screw Anchor Rod 1" Coupler "PISA" D354/ALLIED

Power Hub Screw Anchor Rod Couplings are used to couple additional rods together when further installation depths are needed or to extend the eyenut above grade. The couplers are Hot Dip Galvanized per ASTM A153.

  • These couplings are used with all power hub rods when additional rods must be installed
  • Ultimate Tensile Strength 36,000Lbs
  • 3/4" & 1" Coupling

Our Price: $7.89
SALE Price: $6.14
You save $1.75!
Power Hub Screw Anchor Rod 5/8" Coupler "PISA" D-352 Power Hub Screw Anchor Rod 5/8" Coupler "PISA" D352

Power Hub Screw Anchor Rod Couplings are used to couple additional rods together when further installation depths are needed or to extend the eyenut above grade. The couplers are Hot Dip Galvanized per ASTM A153.

  • These couplings are used with all power hub rods when additional rods must be installed
  • Ultimate Tensile Strength 16,000Lbs
  • 5/8" Coupling

Our Price: $15.07
SALE Price: $11.72
You save $3.35!
Rock Anchor JR172L 1" -72" Length Rock Anchor 1" -72" Length JR172L

1" X 72" Expanding Rock Anchor 36,000 lbs. Unlimited strength

Rock Anchors are installed into core holes bored into rock. The Rock Anchor is tightened along the anchor shaft to expand the resistance wedges into the rock.

To install anchor, drill a 12" deep hole in solid rock, put anchor in hole, turn rod until anchor expands and wedges in the hole.

  • Anchor consists of two Malleable castings and a Triple Eye Anchor Rod.
  • Anchor diameter is 2-1/4".
  • Anchor size expanded is 3-1/8".
  • Hole diameter is 2-3/8".
  • The harder the pull on the rod, the tighter it wedges into the rock.

Our Price: $153.22
Rock Anchor JR130L 1"-30" Length Rock Anchor 1"-30" Length JR130L

1" X 30" Expanding Rock Anchor 36,000 lbs. Unlimited strength

Rock Anchors are installed into core holes bored into rock. The Rock Anchor is tightened along the anchor shaft to expand the resistance wedges into the rock.

To install anchor, drill a 12" deep hole in solid rock, put anchor in hole, turn rod until anchor expands and wedges in the hole.

  • Anchor consists of two Malleable castings and a Triple Eye Anchor Rod.
  • Anchor diameter is 2-1/4".
  • Anchor size expanded is 3-1/8".
  • Hole diameter is 2-3/8".
  • The harder the pull on the rod, the tighter it wedges into the rock.

Our Price: $132.87
Rock Anchor JR153L 1"-53" Length Rock Anchor 1"-53" Length JR153L

1" X 53" Expanding Rock Anchor 36,000 lbs. Unlimited strength

Rock Anchors are installed into core holes bored into rock. The Rock Anchor is tightened along the anchor shaft to expand the resistance wedges into the rock.

To install anchor, drill a 12" deep hole in solid rock, put anchor in hole, turn rod until anchor expands and wedges in the hole.

  • Anchor consists of two Malleable castings and a Triple Eye Anchor Rod.
  • Anchor diameter is 2-1/4".
  • Anchor size expanded is 3-1/8".
  • Hole diameter is 2-3/8".
  • The harder the pull on the rod, the tighter it wedges into the rock.

Our Price: $154.51
Rock Anchor JR196L 1"-96" Length Rock Anchor 1"-96" Length JR196L

1" X 96" Expanding Rock Anchor 36,000 lbs. Unlimited strength

Rock Anchors are installed into core holes bored into rock. The Rock Anchor is tightened along the anchor shaft to expand the resistance wedges into the rock.

To install anchor, drill a 12" deep hole in solid rock, put anchor in hole, turn rod until anchor expands and wedges in the hole.

  • Anchor consists of two Malleable castings and a Triple Eye Anchor Rod.
  • Anchor diameter is 2-1/4".
  • Anchor size expanded is 3-1/8".
  • Hole diameter is 2-3/8".
  • The harder the pull on the rod, the tighter it wedges into the rock.

Our Price: $117.73
Rock Anchor 3/4 - 30" J3437 Rock Anchor 3/4" - 30" J3437

3/4" X 30" Expanding Rock Anchor 23,000 lbs. Unlimited strength

Rock Anchors are installed into core holes bored into rock. The Rock Anchor is tightened along the anchor shaft to expand the resistance wedges into the rock.

To install anchor, drill a 12" deep hole in solid rock, put anchor in hole, turn rod until anchor expands and wedges in the hole.

  • Anchor consists of two Malleable castings and a Triple Eye Anchor Rod.
  • Anchor diameter is 1-3/4".
  • Anchor size expanded is 2-3/8".
  • Hole diameter is 1-7/8".
  • The harder the pull on the rod, the tighter it wedges into the rock.

Our Price: $71.31
Rock Anchor 3/4 - 53" J3438 Rock Anchor 3/4" - 53" J3438

3/4" X 53" Expanding Rock Anchor 23,000 lbs. Unlimited strength

Rock Anchors are installed into core holes bored into rock. The Rock Anchor is tightened along the anchor shaft to expand the resistance wedges into the rock.

To install anchor, drill a 12" deep hole in solid rock, put anchor in hole, turn rod until anchor expands and wedges in the hole.

  • Anchor consists of two Malleable castings and a Triple Eye Anchor Rod.
  • Anchor diameter is 1-3/4".
  • Anchor size expanded is 2-3/8".
  • Hole diameter is 1-7/8".
  • The harder the pull on the rod, the tighter it wedges into the rock.

Our Price: $78.09
   
 
1 2