Thimble Open, ADSS Drope Cable Dead-Ends 1/2 in; Opening Width - 3/4 in; Eye Width - 1 1/8 in; Eye Length - 2 in; Material - Steel, Plated

THIMBLE OPEN 1/2 Guy Strand J1058

This anchor shackle can be connected to eye bolt on the structure. 30,000LB 1/2" (13mm) shackle 7/8 INSIDE WIDE 5/8 PIN
3.5" INSIDE LENGTH

This anchor shackle can be connected to eye bolt on the structure. 50,000LB

Armor Rod for ADSS .576 - .649 Orang Preformed Line Products AR-0175

Armor Rods are available for ADSS cable protection at locations where Mounting Brackets are in stalled away from Dead-ends. All sets have an overall length of 27" (0.68 meters).

Preformed Line PRODUCTS CE-5259 Clevis Eye 15,000 LBF. Strength

• Body: Ductile Iron, Hot Dip Galvanized
• Hardware: Galvanized Steel
• Cotter Pin: Stainless Steel

• Minimum: .272"
• Maximum: .750"

• (A): 7/16" (11.2 mm)
• (B): 1-1/2" (38.1 mm)
• Wide Clevis (C): 13/16" (20.6 mm)
• Eye Thickness (D): 1/2" (17.5 mm)
• Hole Dia. (E): 11/16" (17.5 mm)
• (F): 1-1/2" (38.1 mm)
• Center to Center (L): 3-1/8" (79.4 mm)
• Pin Diameter: 5/8" (16 mm)
• Overall Length: 4-5/8"
• Vertical Ultimate Strength lbf. (KN): 15,000 lbf (47)

H-PLP CE-5261 Clevis Eye 20,000 LBF. Strength

• Body: Ductile Iron, Hot Dip Galvanized
• Hardware: Galvanized Steel
• Cotter Pin: Stainless Steel

• Minimum: .751"
• Maximum: 1.005"

• (A): 7/16" (11.2 mm)q
• (B): 1-1/2" (38.1 mm)
• Wide Clevis (C): 13/16" (20.6 mm)
• Eye Thickness (D): 3/4" (19.1 mm)
• Hole Dia. (E): 11/16" (17.5 mm)
• (F): 1-1/2" (38.1 mm)
• Center to Center (L): 3-1/8" (79.4 mm)
• Pin Diameter: 5/8" (16 mm)
• Vertical Ultimate Strength lbf. (KN): 20,000 lbf (84)

PLP PREFORMED LINE PRODUCTS GRIP; DEADEND OPEN WIRE .063" DE-2505 Color Code Black

• Helical shape insures low distribution of holding stresses and prevents premature fatigue breakage
• False or Double Dead-ending can be accomplished without cutting the wire
• DE-2505 Galvanized Steel .063" Cable Diameter
• Color Code Black

PLP PREFORMED LINE PRODUCTS GRIP; DEADEND OPEN WIRE .083" DE-2506 Color Code Yellow

There is no quicker, easier way to attach Figure-8 drop wire or cable than with PREFORMED Dead-ends for Figure-8 RG-59/U coaxial cable messenger

• Helical shape insures low distribution of holding stresses and prevents premature fatigue breakage
• False or Double Dead-ending can be accomplished without cutting the wire
• DE-2506 Galvanized Steel .083" Cable Diameter
• Color Code YELLOW

PLP PREFORMED LINE PRODUCTS GRIP; DEADEND OPEN WIRE .109" GDE-2501 Color Code Black

• Helical shape insures low distribution of holding stresses and prevents premature fatigue breakage
• False or Double Dead-ending can be accomplished without cutting the wire
• GDE-2501 Galvanized Steel .109" Cable Diameter
• Color Code Black

PLP PREFORMED LINE PRODUCTS GRIP; DEADEND OPEN WIRE .120" GDE-2502 Color Code Green

• Helical shape insures low distribution of holding stresses and prevents premature fatigue breakage
• False or Double Dead-ending can be accomplished without cutting the wire
• GDE-2502 Galvanized Steel .120" Cable Diameter
• Color Code GREEN

PLP PREFORMED LINE PRODUCTS GRIP; DEADEND OPEN WIRE .134" GDE-2503 Color Code Orange

• Helical shape insures low distribution of holding stresses and prevents premature fatigue breakage
• False or Double Dead-ending can be accomplished without cutting the wire
• GDE-2503 Galvanized Steel .134" Cable Diameter
• Color Code Orange

Fixed Crossarm Systems are Crossarms that are bolted together with a vertical member that can be bolted or banded to the structure. The FIBERLIGN® ADSS Cable Storage supports a 33" loop diameter.

For Wood Pole, Metal Pole & Lattice Tower. 2.75' loop dia. x 150 ft long to 3/4" dia. Cable.

The PLP FIBERLIGN® Tangent Support (FTS) offers another method of supporting ADSS Drop Cables with excellent unbalance load capability and bend relief support. This product is designed to connect directly to J-hooks for a economical alternative. One FTS can reduce pole clutter by replacing two Dead-end and j-hook connections.

ADSS Drop Cable Dead-end & ADSS Midspan Drop for FTTP .371 - .380 .94-.96YEL 26 (660) (NO THIMBLE) DROP CABLE DE ADSS 288811353 .371 - .380 9.4 - 9.6 Yellow 26
FIBERLIGN® ADSS Drop Cable Dead-end is able to secure the soft pliable surface of a drop cable without causing attenuation. Unlike wedge type Dead-ends, the formed wire Dead-end effectively transfers the axial load on the cable at the end of the Dead-end legs to a low uniform radial compression near the dead end loop. This transition of force is distributed over the length of the product thus allowing secure holding capability with minimized pressure on the cable or messenger.

The Preformed Line Products FIBERLIGN Aluminum Support (FAS) is designed to gently, but firmly support All-Dielectric Self-Supporting (ADSS) cable. The FAS features the following: Integrated bolt or band mount design, Hinged keeper and base, Single-bolt clamping, and Stackability for multi-cable installations. The band slot is designed to accept a 1 1/4" wide x 0.040" thick (32mm x 1 mm) high strength band.

The PREFORMED LINE PRODUCTS FIBERLIGN Dielectric Support (FDS) system is designed to gently, but firmly, support All-Dielectric Self-Supporting (ADSS) cable. It is intended for tangent support installations on lines that feature relatively low voltages, short spans and modest mechanical loads.

ADSS Drop Cable Dead-end & ADSS Midspan Drop for FTTP .371 - .380 .94-.96YEL 26 (660)W/THIMBLE DROP CABLE DE ADSS 288811353 .371 - .380 9.4 - 9.6 Yellow 26
FIBERLIGN® ADSS Drop Cable Dead-end is able to secure the soft pliable surface of a drop cable without causing attenuation. Unlike wedge type Dead-ends, the formed wire Dead-end effectively transfers the axial load on the cable at the end of the Dead-end legs to a low uniform radial compression near the dead end loop. This transition of force is distributed over the length of the product thus allowing secure holding capability with minimized pressure on the cable or messenger.

The Preformed Line Products FIBERLIGN Aluminum Support (FAS) is designed to gently, but firmly support All-Dielectric Self-Supporting (ADSS) cable. The FAS features the following: Integrated bolt or band mount design, Hinged keeper and base, Single-bolt clamping, and Stackability for multi-cable installations. The band slot is designed to accept a 1 1/4" wide x 0.040" thick (32mm x 1 mm) high strength band.

The Preformed Line Products Heavy-Duty FIBERLIGN® Aluminum Suspension Kit with Structural Reinforcing Rods and Anchor Shackle is designed to gently, but firmly support All-Dielectric Self-Supporting (ADSS) cable. The FASN features the following: Interlocking Hinge, Single-bolt clamping, Short to Medium Span Option, Low to High Voltage Environment acceptance.

The Preformed Line Products Heavy-Duty FIBERLIGN® Aluminum Suspension Kit with Structural Reinforcing Rods is designed to gently, but firmly support All-Dielectric Self-Supporting (ADSS) cable. The FASN features the following: Interlocking Hinge, Single-bolt clamping, Short to Medium Span Option, Low to High Voltage Environment acceptance.

The Preformed Line Products FIBERLIGN Dielectric Dead-end product line has been designed to securely but gently terminate All Dielectric Self-Supporting (ADSS) aerial fiber optic cable.

Preformed Line Products FIBERLIGN® Dielectric Dead-end Kit for ADSS

Dead-end component is required to transfer axial tensile loads and distribute radial compressive forces through the plastic jacket and onto the internal strength members without damaging the fragile plastic jacket or internal optical fibers.

Preformed Line Products FIBERLIGN® Dielectric Dead-end Kit for ADSS
Dead-end component is required to transfer axial tensile loads and distribute radial compressive forces through the plastic jacket and onto the internal strength members without damaging the fragile plastic jacket or internal optical fibers.

Preformed Line Products FIBERLIGN® Dielectric Limited Tension Dead-end Only for ADSS
Dead-end component is required to transfer axial tensile loads and distribute radial compressive forces through the plastic jacket and onto the internal strength members without damaging the fragile plastic jacket or internal optical fibers.

Preformed Line Products FIBERLIGN® Dielectric Limited Tension Dead-end Only for ADSS
Dead-end component is required to transfer axial tensile loads and distribute radial compressive forces through the plastic jacket and onto the internal strength members without damaging the fragile plastic jacket or internal optical fibers.

Preformed Line Products FIBERLIGN® Dielectric Medium Tension Dead-end Only for ADSS
Designed for medium tension applications. Holding performance will vary by specific cable brand and operating conditions.

Preformed Line Products FIBERLIGN® Dielectric Medium Tension Dead-end Only for ADSS
Dead-end component is required to transfer axial tensile loads and distribute radial compressive forces through the plastic jacket and onto the internal strength members without damaging the fragile plastic jacket or internal optical fibers.

Preformed Line Products FIBERLIGN® Dielectric Dead-end Kit for ADSS
Dead-end component is required to transfer axial tensile loads and distribute radial compressive forces through the plastic jacket and onto the internal strength members without damaging the fragile plastic jacket or internal optical fibers.
ADSS Dead End Kits ADSS Dead Ends ADSS Self Support

Preformed Line Products FIBERLIGN® Dielectric Dead-end Kit for ADSS
Dead-end component is required to transfer axial tensile loads and distribute radial compressive forces through the plastic jacket and onto the internal strength members without damaging the fragile plastic jacket or internal optical fibers.

Preformed Line Products FIBERLIGN® Dielectric Dead-end Kit for ADSS
Dead-end component is required to transfer axial tensile loads and distribute radial compressive forces through the plastic jacket and onto the internal strength members without damaging the fragile plastic jacket or internal optical fibers.

Preformed Line Products FIBERLIGN® Dielectric Dead-end Kit for ADSS
Dead-end component is required to transfer axial tensile loads and distribute radial compressive forces through the plastic jacket and onto the internal strength members without damaging the fragile plastic jacket or internal optical fibers.

Preformed Line Products FIBERLIGN® Dielectric Dead-end ONLY for ADSS
Dead-end component is required to transfer axial tensile loads and distribute radial compressive forces through the plastic jacket and onto the internal strength members without damaging the fragile plastic jacket or internal optical fibers.

Preformed Line Products FIBERLIGN® Dielectric Dead-end ONLY for ADSS
Dead-end component is required to transfer axial tensile loads and distribute radial compressive forces through the plastic jacket and onto the internal strength members without damaging the fragile plastic jacket or internal optical fibers.

The PREFORMED LINE PRODUCTS FIBERLIGN Dielectric Support (FDS) system is designed to gently, but firmly, support All-Dielectric Self-Supporting (ADSS) cable. It is intended for tangent support installations on lines that feature relatively low voltages, short spans and modest mechanical loads.

The PREFORMED LINE PRODUCTS FIBERLIGN Dielectric Support (FDS) system is designed to gently, but firmly, support All-Dielectric Self-Supporting (ADSS) cable. It is intended for tangent support installations on lines that feature relatively low voltages, short spans and modest mechanical loads.

The Preformed Line Products FIBERLIGN Dielectric Support (FDS) system is designed to gently, but firmly, support All-Dielectric Self-Supporting (ADSS) cable. It is intended for tangent support installations on lines that feature relatively low voltages, short spans and modest mechanical loads.

The PLP FIBERLIGN® Downlead Cushion secures Optical Ground Wire (OPGW) downleads or ADSS cable downleads to structures while minimizing compressive clamping forces which could be transferred to the optical elements.

H-PLP8003041, H-PLP8003043, H-PLP8003044
8003041, 8003043, 8003044

Preformed Line Products FIBERLIGN® Lite DUAL Support Housing for ADSS
Designed to gently but firmly support All Dielectric Self-Supporting (ADSS) cable. It is intended for tangent support installations on lines that feature low voltages, very short spans and low mechanical loads. Comes with no Inserts
HOUSING ONLY

The Preformed Line Products FIBERLIGN Lite Support (FLS) system is designed to gently but firmly support All Dielectric Self-Supporting (ADSS) cable. It is intended for tangent support installations (see “LINE ANGLES”) on lines that feature low voltages, very short spans and low mechanical loads. For products with higher capabilities see the subsequent pages under FIBERLIGN® Dielectric Support, FIBERLIGN Aluminum Support, FIBERLIGN Aluminum Suspension, with and without rods and FIBERLIGN Dielectric Suspension. The two latter products can be used in higher voltage environments where track resistant ADSS cables.
Cable Diameter:

• Minimum: .550" (14 mm)
• Maximum: .579" (14.7 mm)

The Preformed Lien Products FIBERLIGN Lite Support (FLS) system is designed to gently but firmly support All Dielectric Self-Supporting (ADSS) cable. It is intended for tangent support installations (see "LINE ANGLES") on lines that feature low voltages, very short spans and low mechanical loads. For products with higher capabilities see the subsequent pages under FIBERLIGN® Dielectric Support, FIBERLIGN Aluminum Support, FIBERLIGN Aluminum Suspension, with and without rods and FIBERLIGN Dielectric Suspension. The two latter products can be used in higher voltage environments where track resistant ADSS cables are required.

The Preformed Lien Products FIBERLIGN Lite Support (FLS) system is designed to gently but firmly support All Dielectric Self-Supporting (ADSS) cable. It is intended for tangent support installations (see "LINE ANGLES") on lines that feature low voltages, very short spans and low mechanical loads. For products with higher capabilities see the subsequent pages under FIBERLIGN® Dielectric Support, FIBERLIGN Aluminum Support, FIBERLIGN Aluminum Suspension, with and without rods and FIBERLIGN Dielectric Suspension. The two latter products can be used in higher voltage environments where track resistant ADSS cables are required.

The PLP FIBERLIGN Lite Support (FLS) system is designed to gently but firmly support All Dielectric Self-Supporting (ADSS) cable. It is intended for tangent support installations (see "LINE ANGLES") on lines that feature low voltages, very short spans and low mechanical loads. For products with higher capabilities see the subsequent pages under FIBERLIGN® Dielectric Support, FIBERLIGN Aluminum Support, FIBERLIGN Aluminum Suspension, with and without rods and FIBERLIGN Dielectric Suspension. The two latter products can be used in higher voltage environments where track resistant ADSS cables are required.

The PLP FIBERLIGN Lite Support (FLS) system is designed to gently but firmly support All Dielectric Self-Supporting (ADSS) cable. It is intended for tangent support installations (see "LINE ANGLES") on lines that feature low voltages, very short spans and low mechanical loads. For products with higher capabilities see the subsequent pages under FIBERLIGN® Dielectric Support, FIBERLIGN Aluminum Support, FIBERLIGN Aluminum Suspension, with and without rods and FIBERLIGN Dielectric Suspension. The two latter products can be used in higher voltage environments where track resistant ADSS cables are required.

The PLP FIBERLIGN® Tangent Support (FTS) offers another method of supporting ADSS Drop Cables with excellent unbalance load capability and bend relief support. This product is designed to connect directly to J-hooks for a economical alternative. One FTS can reduce pole clutter by replacing two Dead-end and j-hook connections.