• Cable Diameter Range: 0.21-0.35"
• Approx. Breaking Point: 1,400 lbs.
• Eye Length: 7-1/2"
• Mesh Length: 14"

Double/Single weave mesh, galvanized steel for outside plant cable. Used for the installation of fiber optic communication lines either underground, overhead, through conduit or through enclosures. They will fit single cables or cable bundles, are easily installed on the cable and are reusable.
Fiber Optic - Flexible Eye, Double/Single Weave, Low Profile Grip

• Cable Diameter Range: 0.10-0.22"
• Approx. Breaking Strength: 900 lbs.
• Eye Length: 7-1/2"
• Mesh length: 10"

Condux 08761842 Fixed Head Innerduct Pulling Eye 1"-1 1/4", 1.06-143"
Tapered buttress threads thread into the innerduct for maximum pulling strength. These eyes connect directly to a Condux Swivel. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.

Double/Single weave mesh, galvanized steel for outside plant cable. Used for the installation of fiber optic communication lines either underground, overhead, through conduit or through enclosures. They will fit single cables or cable bundles, are easily installed on the cable and are reusable.
Fiber Optic - Flexible Eye, Double/Single Weave, Low Profile Grip

• Cable Diameter Range: 0.53-0.74"
• Approx. Breaking Strength: 3,000 lbs.
• Eye Length: 8-1/2"
• Mesh Length: 23"

Double/Single weave mesh, galvanized steel for outside plant cable. Used for installation of fiber optic communication lines either underground, overhead, through enclosures. They will fit single cables or cables bundles, are easily installed on the cable and are reusable.
Fiber Optic - Low Profile, Double/Single Weave, Low Profile Grip

• Cable Diameter Range: 0.42-0.61"
• Approx. Breaking Strength: 2,500 lbs.
• Eye Length: 8-1/2"
• Mesh Length: 21"

Double/Single weave mesh, galvanized steel for outside plant cable. Used for installation of fiber optic communication lines either underground, overhead, through conduit or through enclosures. They will fit single cables or cable bundles, are easily installed on the cable and are reusable.
Fiber Optic - Flexible Eye, Double/Single Weave, Low Profile Grip

• Cable Diameter Range: 0.75-1.00"
• Approx. Breaking Strength: 2,500 lbs.
• Eye Length: 8-1/2"
• Mesh Length: 28"

The GMP Double Weave Pulling Grip is manufactured for high-tensile, galvanized steel wire that is evenly hand woven in a single, double or triple wire weave according to pulling tension requirements. GMP reverse weave our grips which create a loop at the end of the grip instead of being crimped or soldered together. the wire is then joined under the crimped head. This creates a higher quality product that outlasts competition.
Double Weave Single Flexible Eye
Cable Diameter: 0.33-0.78" (10-20mm)
Grip Length: 23.62" (600mm)
Min. Breaking Strength: 4101 lbs.

Condux 08017200 Breakaway Swivel 5/8" 600 lbs.
Essential for fiber optic and coaxial cable pulling, these swivels have a break load ranging from 150–1,800 pounds (667–8,006 N) and are designed to separate at ±10% of their rated break load. If the load rating is exceeded, the interior break pin fractures, the swivel separates, and the cable remains undamaged.
SUB - GMP71408

Condux 08761844 Fixed Head Innerduct Pulling Eye 1.5", 1.37-1.68"
Tapered buttress threads thread into the innerduct for maximum pulling strength. These eyes connect directly to a Condux Swivel. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.

Condux 08761846 Fixed Head Innerduct Pulling Eye 2", 1.80-2.19"
Tapered buttress threads thread into the innerduct for maximum pulling strength. These eyes connect directly to a Condux Swivel. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.

Condux 08914130 Fixed Head Innerduct Pulling Eye 1-1/4", 1.06" -1.43"
Tapered buttress threads thread into the innerduct for maximum pulling strength. These eyes connect directly to a Condux Swivel. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.
SUB - GMP60512

Condux 08914140 Fixed Head Innerduct Pulling Eye 1-1/2", 1.37"-1.68"
Tapered buttress threads thread into the innerduct for maximum pulling strength. These eyes connect directly to a Condux Swivel. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.
SUB - GMP60515

Condux 08914150 Fixed Head Innerduct Pulling Eye 1-3/4", 1.68"-1.81"
Tapered buttress threads thread into the innerduct for maximum pulling strength. These eyes connect directly to a Condux Swivel. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.

Condux 08914160 Fixed Head Innerduct Pulling Eye 2", 1.93"-2.12"
Tapered buttress threads thread into the innerduct for maximum pulling strength. These eyes connect directly to a Condux Swivel. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.
SUB - GMP60520

Condux 08914120 Fixed Head Innerduct Pulling Eye 1", 0.93"-1.06"
Tapered buttress threads thread into the innerduct for maximum pulling strength. These eyes connect directly to a Condux Swivel. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.
SUB - GMP60510

Condux 08960712 Pulling Eye, Inner-Duct 1-1/4" Swivel Head

Condux 08960715 Pulling Eye, Inner-Duct 1.37" - 1.50" Swivel Head
The Inner-duct Pulling Eye is a hybrid tool that combines features from standard inner-duct pulling eyes and Condux swivels. A swivel head prevents twisting and binding of the inner-duct as it is installed. It eliminates the need for a separate swivel on each pulling eye when installing single innerducts into individual conduits or multiple inner-ducts into a single conduit. Its short length is an advantage on tight bends compared to using a separate swivel and pulling eye. Easily installed using a 1-3⁄8" deep socket or adjustable wrench.
SUB - GMP61515

Condux 08960720 Pulling Eye, Inner-Duct 2" Swivel Head
The Inner-duct Pulling Eye is a hybrid tool that combines features from standard inner-duct pulling eyes and Condux swivels. A swivel head prevents twisting and binding of the inner-duct as it is installed. It eliminates the need for a separate swivel on each pulling eye when installing single innerducts into individual conduits or multiple inner-ducts into a single conduit. Its short length is an advantage on tight bends compared to using a separate swivel and pulling eye. Easily installed using a 1-3⁄8" deep socket or adjustable wrench.
SUB - GMP61520

Offers a quick and easy way to connect pulling eyes or swivels to winch lines, harnesses or rope. To close, simply screw the nut onto the threaded end. Connectors are reusable.

Offers a quick and easy way to connect pulling eyes or swivels to winch lines, harnesses or rope. To close, simply screw the nut onto the threaded end. Connectors are reusable.

Offers a quick and easy way to connect pulling eyes or swivels to winch lines, harnesses or rope. To close, simply screw the nut onto the threaded end. Connectors are reusable.

Offers a quick and easy way to connect pulling eyes or swivels to winch lines, harnesses or rope. To close, simply screw the nut onto the threaded end. Connectors are reusable.

Offers a quick and easy way to connect pulling eyes or swivels to winch lines, harnesses or rope. To close, simply screw the nut onto the threaded end. Connectors are reusable.

Offers a quick and easy way to connect pulling eyes or swivels to winch lines, harnesses or rope. To close, simply screw the nut onto the threaded end. Connectors are reusable.

Double/Single weave mesh, galvanized steel for outside plant cable. Used for the installation of fiber optic communication lines either underground, overhead, through conduit or through enclosures. They will fit single cables or cable bundles, are easily installed on the cable and are reusable.
Fiber Optic - Flexible Eye, Double/Single Weave, Low Profile Grip

• Cable Diameter Range: 0.32-0.48"
• Approx. Breaking Strength: 2,000 lbs.
• Eye Length: 8-1/2"
• Mesh Length: 19"

Fiber Optic Slack Grip - Split Mesh, Rod Closing, Single Weave steel for outside plant cable. Used for the installation of fiber optic communication lines either underground, overhead, through conduit or through enclosures. They will fit single cables or cable bundles, are easily installed on the cable and are reusable.

Condux 08017000 - 808 Champion Swivel 5/8" 600 lbs.(Not a Breakaway swivel)
Condux Ball Bearing Swivels are designed to the highest specifications for underground and overhead pulling applications. All swivels are tested and inspected to ISO 9001:2000 quality standards. This ensures the customer is getting the most reliable and safest swivel on the market. All swivels are precision machined from high grade stainless steel. Clevis pins are heat treated to prevent pin damage when using steel shackles. Each swivel is manufactured with three angular contact or deep groove ball bearings, which allow the swivel to rotate beyond its rated load. Most manufacturers use only one bearing to handle the load, causing the swivels to stop rotating before it reaches the recommended workload.

Condux 08017205 Replacement Breakaway Pin for 5/8" Swivel 600 lbs.
Condux Breakaway Swivel are essential for fiber optic and coaxial cable pulling, these swivels have a break load ranging from 150-1,800 lbs. (667-8,006 N) and are designed to separate at 5 percent of their rated break load. If the load rating is exceeded, the interior break pin fractures, the swivel separates, and the cable remains undamaged.
Replacement Breakaway Pin for 5/8" Swivel
Workload: 600 lbs.

Condux 08017700 Breakaway Swivel 7/8" 1700 lbs

Essential for fiber optic and coaxial cable pulling, there swivels have a break load ranging from 150-1,800 pounds (667-8,006 N) and are designed to separate at ±10% of their rated break load. If the load rating exceeded, the interior break pin fractures, the swivel separates and the cable undamaged.

GMP 71408 Breakaway Swivel 5/8"600LB
Breakaway Swivel 5/8" 600LB GMP 71408. 5/8 in. (15.88 mm) made from Steel. Our Break-away Swivels give you invaluable protection when pulling either fiber optic or coaxial cable.These simple tools provide an inexpensive fracture point between the pulling line and cable avoiding costly cable damage if the cable's rated pulling capacity is exceeded. The 5/8 in. size is extremely convenient when working with innerduct sizes below 1-5/8 in. in diameter. The design of the swivels incorporates a replaceable tension bolt that joins the barrel eye and swivel body. The bolt separates when pulling loads on the cable reach +/-5%. The damaged bolt can then be replaced in seconds using an Allen Breakaway BoltWrench (included) and screwdriver.
SUB - CON 08017200

GMP 53703 Breakaway Swivel 800LB 7/8"
Breakaway Swivel 7/8" 800LB GMP 53703. 7/8 in. (22.23 mm) made from high quality aluminum. Break-Away Swivels provide an inexpensive fracture point between a pulling line & fiber optic cable to protect against costly cable damage if the cable's rated pulling capacity is exceeded. The 7/8" x 4 5/8" body is made of high quality aluminum alloy with a black anodized finish for wear resistance. Steel thrust washers and bushings insure smooth rotation under load and help to keep twisting forces from reaching the cable. Each unit comes with a replaceable color-coded tension bolt. The swivel & bolt are color-coded for identification. The bolt will separate when the pulling load reaches +/-5% of the bolt rating. It can then be replaced using an Allen Wrench (included) & screwdriver.
SUB - CON 08018700

GMP70137 SWIVEL 5000 LBS
4-5/32 LENGTH, SLOT PIN
SWIVEL HEAVY DUTY 17/32
EYE WIDTH, 1-1/4 DIAMETER,

These tough swivels are designed to handle higher thrust loads for extra cable safety and faster straight pulls. These heavy-duty swivels are built with a thrust bearing for tensile load and a radial bearing for bending load.
SUB - CON08080912

Breakaway Swivel 5/8" 450LB GMP 71406. 5/8 in. (15.88 mm) made from Steel. Our Break-away Swivels give you invaluable protection when pulling either fiber optic or coaxial cable.These simple tools provide an inexpensive fracture point between the pulling line and cable avoiding costly cable damage if the cable's rated pulling capacity is exceeded. The 5/8 in. size is extremely convenient when working with innerduct sizes below 1-5/8 in. in diameter. The design of the swivels incorporates a replaceable tension bolt that joins the barrel eye and swivel body. The bolt separates when pulling loads on the cable reach +/-5%. The damaged bolt can then be replaced in seconds using an Allen Breakaway BoltWrench (included) and screwdriver.
SUB - CON 08016900

GMP 53701 Breakaway Swivel 7/8" 450 LB

Breakaway Swivel 7/8" 450LB GMP 53701. 7/8 in. (22.23 mm) made from high quality aluminum. Break-away Swivels give you invaluable protection when pulling either fiber optic or coaxial cable. These simple tools provide an inexpensive fracture point between the pulling line and cable avoiding costly cable damage if the cable's rated pulling capacity is exceeded. The design of the swivels incorporates a replaceable tension bolt that joins the barrel eye and swivel body. The bolt separates when pulling loads on the cable reach +/-5%. The damaged bolt can then be replaced in seconds using an Allen Breakaway BoltWrench (included) and screwdriver.
SUB - CON 08015800

These medium duty, long length closed-mesh wire pulling grips from Klein combine strength and durability to help linemen get the job done. Manufactured, inspected and tested in the USA, these grips are made of drop forged quality US steel. Grips ate rigorously tested using the Magnuflux method and pulled to rated load to ensure the highest quality and reliability.
Double Weave, Rotating-Eye Pulling Grip

• KPS Heavy Duty-Medium Length
• Cable Diameter Range: 1.00-1.24"
• Approx. Breaking Strength: 2,560 lbs.
• Mesh Length: 20"

These medium duty, long length closed-mesh wire pulling grips from Klein combine strength and durability to help linemen get the job done. Manufactured, inspected and tested in the USA, these grips are made of drop forged quality US steel. Grips are rigorously tested using the Magnuflux method and pulled to rated load to ensure the highest quality and reliability.
Double Weave, Rotating-Eye Pulling Grip

• KPS Heavy Duty-Medium Length
• Cable Diameter Range: 0.50-0.61"
• Approx. Breaking Strength: 1,120 lbs.
• Mesh Length: 16"

These medium duty, long length closed-mesh wire pulling grips from Klein combine strength and durability to help linemen get the job done. Manufactured, inspected and tested in the USA, these grips are made of drop forged quality US steel. Grips are rigorously tested using the Magnuflux method and pulled to rated load to ensure the highest quality and reliability.
Double Weave, Rotating-Eye Pulling Grip

• KPS Heavy Duty-Medium Length
• Cable Diameter Range: 1.00-1.49"
• Approx. Breaking Strength: 3,280 lbs.
• Mesh Length: 33"

These junior duty, closed-mesh wire pulling grips from Klein combine strength and durability to help linemen get the job done. Manufactured, inspected and tested in the USA, these grips are made of drop forged quality US steel. Grips are rigorously tested using the Magnuflux method and pulled to rated load to ensure the highest quality and reliability.
Single Weave, Flexible-Eye Pulling Grip

• Cable Diameter Range: 1.00-1.24"
• Approx. Breaking Strength: 780 lbs.
• Mesh Length: 11.5"

These junior duty, closed-mesh wire pulling grips from Klein combine strength and durability to help linemen get the job done. Manufactured, inspected and tested in the USA, these grips are made of drop forged quality US steel. Grips are rigorously tested using the Magnuflux method and pulled to rated load to ensure the highest quality and reliability.
Junior Duty Single Weave, Flexible-Eye Pulling Grip

• Cable Diameter Range: 0.75"-0.99"
• Approx. Breaking Strength: 560 lbs.
• Mesh Length: 10"

These medium duty, long length closed-mesh wire pulling grips from Klein combine strength and durability to help linemen get the job done. Manufactured, inspected and tested in the USA, these grips are made of drop forged quality US steel. Grips are rigorously tested using the Magnuflux method and pulled to rated load to ensure the highest quality and reliability.
Double Weave, Rotating-Eye Pulling Grip

• KPS Heavy Duty-Medium Length
• Cable Diameter Range: 2.50-2.99"
• Approx. Breaking Strength: 6,600 lbs.
• Mesh Length: 28"

These medium duty, long length closed-mesh wire pulling grips from Klein combine strength and durability to help linemen get the job done. Manufactured, inspected and tested in the USA, these grips are made of drop forged quality US steel. Grips ate rigorously tested using the Magnuflux method and pulled to rated load to ensure the highest quality and reliability.
Double Weave, Rotating-Eye Pulling Grip

• KPS Heavy Duty-Medium Length
• Cable Diameter Range: 1.50-1.99"
• Approx. Breaking Strength: 3,280 lbs.
• Mesh Length: 25"

These medium duty, long length closed-mesh wire pulling grips from Klein combine strength and durability to help linemen get the job done. Manufactured, inspected and tested in the USA, these grips are made of drop forged quality US steel. Grips ate rigorously tested using the Magnuflux method and pulled to rated load to ensure the highest quality and reliability.
Double Weave, Flexible-Eye Pulling Grip

• Cable Diameter Range: 0.50-0.61"
• Approx. Breaking strength: 480 lbs.
• Mesh Length: 13"

These medium duty, long length closed-mesh wire pulling grips from Klein combine strength and durability to help linemen get the job done. Manufactured, inspected and tested in the USA, these grips are made of drop forged quality US steel. Grips are rigorously tested using the Magnuflux method and pulled to rated load to ensure the highest quality and reliability.
Double Weave, Rotating Eye Pulling Grip

• KPS Heavy Duty Medium Length
• Cable Diameter Range: 0.62-0.74"
• Approx. Breaking Length: 1,360 lbs.
• Mesh Length: 16"

These medium duty, long length closed-mesh wire pulling grips from Klein combine strength and durability to help linemen get the job done. Manufactured, inspected and tested in the USA, these grips are made of drop forged quality US steel. Grips ate rigorously tested using the Magnuflux method and pulled to rated load to ensure the highest quality and reliability.
Double Weave, Rotating-Eye Pulling Grip

• KPS Heavy Duty Medium Length
• Cable Diameter Range: 2.00-2.49"
• Approx. Breaking Strength: 5,440 lbs.
• Mesh Length: 26"

These medium duty, long length closed-mesh wire pulling grips from Klein combine strength and durability to help linemen get the job done. Manufactured, inspected and tested in the USA, these grips are made of drop forged quality US steel. Grips ate rigorously tested using the Magnuflux method and pulled to rated load to ensure the highest quality and reliability.
Double Weave, Rotating-Eye Pulling Grips

• KPS Heavy Duty-Medium Length
• Cable Diameter Range: 3.50-3.99"
• Approx. Breaking Length: 9,600 lbs.
• Mesh Length; 32"

These medium duty, long length closed-mesh wire pulling grips from Klein combine strength and durability to help linemen get the job done. Manufactured, inspected and tested in the USA, these grips are made of drop forged quality US steel. Grips are rigorously tested using the Magnuflux method and pulled to rated load to ensure the highest quality and reliability.
Double Weave, Rotating Eye Pulling Grip

• KPS Heavy Duty-Medium Length
• Cable Diameter Range: 0.75-0.99"
• Approx. Breaking Strength: 1,360 lbs.
• Mesh Length: 20"

Split Mesh pulling-grips are used for pulling overhead or underground cable, stringing service or communication
lines into buildings, pulling wire through conduit,
and general underground construction.
Slack-Pulling, Offset Flexible Eye Pulling Grip

• KSRK Light Duty-standard Length
• Cable Diameter Range: 0.75-0.99"
• Approx. Breaking Strength: 480 lbs.
• Mesh Length: 12"
• Split Grip mesh pulling Grip

This Strand Jig Puller is used to pull out cable prior to the lashing operation. The main body of the Puller is a rugged one-piece aluminum casting.

This unit is designed to pull out up to four cables and works on packages up to 2 3/4" diameter. Opposing roller arms retain the puller to the existing cable and offer quick pole transfer.

Heavy Duty Ball Bearing Swivels are available in Models HD-00, HD-0, HD-1, HD-2, HD-3 and HD-4.

Each model is different in size, specifications and ratings; but they all have the same basic design. They are specifically designed for tension stringing, and assure that conductor will remain in the neutral position during stringing of transmission or distribution lines.

These twin race ball bearing swivels are manufactured from high-grade pre-stressed steel. Proper placement of thrust and radial bearing allow thrust and shock loads to be absorbed without affecting rotation of swivel. Pins are screwdriver removable.

Swivel Eye Pulling Grip - Lewis SEG-3
Swivel Eye Grips are available with hardened steel rotating eyes. The eyes are durable, compact, and streamlined and will thread through blocks and sheaves without binding. The rotating eye is not a ball bearing swivel and will not turn under tension.
Mesh length 48" Size Range: 1.5" - 2.0" Working load 11,200 lbs..

Swivel Eye Pulling Grip - Lewis SEG-0
The SEC Series are available with hardened steel rotating eyes. The eyes are durable, compact, and streamlined and will thread through blocks and sheaves without binding. The rotating eye is not a ball bearing swivel and will not turn under tension. It will turn to relieve pulling torque when the pulling tension is released.
Mesh length 24" Size Range: .25"- .50" Working load 1,200 lbs.

Swivel Eye Pulling Grip - Lewis SEG-1
Swivel Eye Grips are available with hardened steel rotating eyes. The eyes are durable, compact, and streamlined and will thread through blocks and sheaves without binding. The rotating eye is not a ball bearing swivel and will not turn under tension.
Mesh length 36" Size Range: .50" - 1.0" Working load 3,500 lbs.

.

Heavy Duty Ball Bearing Swivels are available in Models HD-00, HD-0, HD-1, HD-2, HD-3 and HD-4.

Each model is different in size, specifications and ratings; but they all have the same basic design. They are specifically designed for tension stringing, and assure that conductor will remain in the neutral position during stringing of transmission or distribution lines.

These twin race ball bearing swivels are manufactured from high-grade pre-stressed steel. Proper placement of thrust and radial bearing allow thrust and shock loads to be absorbed without affecting rotation of swivel. Pins are screwdriver removable.

Double weave construction for medium to heavy pulling applications in underground installations. Additionally its steel forged revolving head is ideal for connecting to Slingco swivels.
Warning:
The Slingco RT Type Rotating Eye Cable Grip does not revolve under load. The rotating eye does not replace the need for a swivel.