5/8 X 10" OVAL EYE BOLT H-J9410

OVAL EYE BOLT H-J9410 5/8 X10"

Eyebolts are forged, one piece design and are commonly used as an attachment point to secure thimbles, clevises, links and deadend insulators. Regular oval eyebolts are supplies with a 4 or 6 inch thread length and one assembled square nut.

Eye I.D. 1-1/2" width x 2" length

• Hot Dip Galvanized

5/8 X 12" OVAL EYE BOLT H-J9412

OVAL EYE BOLT H-J9412 5/8 X12"

Eyebolts are forged, one piece design and are commonly used as an attachment point to secure thimbles, clevises, links and deadend insulators. Regular oval eyebolts are supplies with a 4 or 6 inch thread length and one assembled square nut.

Eye I.D. 1-1/2" width x 2" length

• Hot Dip Galvanized

5/8 X 14" OVAL EYE BOLT J9414

OVAL EYE BOLT H-J9414 5/8 X14"

Eyebolts are forged, one piece design and are commonly used as an attachment point to secure thimbles, clevises, links and deadend insulators. Regular oval eyebolts are supplies with a 4 or 6 inch thread length and one assembled square nut.

Eye I.D. 1-1/2" width x 2" length

• Hot Dip Galvanized

5/8 X 18" OVAL EYE BOLT J9418

OVAL EYE BOLT H-J9418 5/8 X18"

Eyebolts are forged, one piece design and are commonly used as an attachment point to secure thimbles, clevises, links and deadend insulators. Regular oval eyebolts are supplies with a 4 or 6 inch thread length and one assembled square nut.

Eye I.D. 1-1/2" width x 2" length

• Hot Dip Galvanized

5/8 x 8" OVAL EYE BOLT H-J9408

OVAL EYE BOLT H-J9408 5/8 X8"

Eyebolts are forged, one piece design and are commonly used as an attachment point to secure thimbles, clevises, links and deadend insulators. Regular oval eyebolts are supplies with a 4 or 6 inch thread length and one assembled square nut.

Eye I.D. 1-1/2" width x 2" length

• Hot Dip Galvanized

Angled Thimble Eye Bolt 5/8" X 10" J8151

• Minimum thread length is 4".
• Recommended torque value: 73 ft lb.
• Minimum Tensile Strength: 13,550 lbf.

B Cable Suspension Bolt 5/8" X 18" Allied Bolt 8264

Used to secure two cable suspension clamps at opposite sides of utility pole.

• Collars are forged instead of welded for extra strength.
• Bolt provided with cone point at each end to ease starting.
• Hot dip galvanized to meet ASTM Specification F2329.
• Manufacturers mark (ABI) and tensile load designation mark (i.e.10M, 16M, 25M) appear on the unthreaded section of each bolt. ABI marking is registered with the U.S Patent Office per the Fastner Insignia Act.
• Minimum tensile strength: 13,550 lbf.
• Recommended torque value: 73 ft lb.
• Unthreaded section is 6".

Cable Extension Bolt 5/8" x 11" Allied Bolt 2073

• Used for placement of second cable at the same level and side of a pole as the existing cable.
  
• Cable Extension Bolts are designed to attach to the threaded ends of suspension bolts.
  
• Internally threaded section is eight inches long.
  
• External threaded section is three inches long.
  
• Hot dip galvanized to meet ASTM Specification A153.

Cable Extension Bolt 5/8" x 7" Allied Bolt 2070

• Allied Bolt 2070 Used for placement of second cable at the same level and side of a pole as the existing cable.
  
• Cable Extension Bolts are designed to attach to the threaded ends of suspension bolts.
  
• Internally threaded section is four inches long.
  
• External threaded section is three inches long.
  
• Hot dip galvanized to meet ASTM Specification A153.

Cable Extension Bracket 17-1/2" To 26" J7920

H-J7920 ARM CABLE EXTENSION
3 x 2-1/2 x 5/16 Angle Size 17-1/2-26 extension from center of Pole.
hot dip galvanized Telephone cable support.

Cable Extension Bracket 26-1/2" - 44-1/2" J7921

H-J7921 ARM CABLE EXTENSION ARM.
3-1/2 x 2-1/2 x 5/16 Angle Size 26-1/2 - 44-1/2 Extension from center of Pole.
hot dip galvanized telephone cable support.

CABLE EXTENSION ARM H-J7921

Carriage Bolt 1/2" x 2" AF 29556

Aluma-Form 29556 Carriage Bolt 1/2" x 2"
The carriage bolts are roll threaded with square shoulder and square nut for Stand Off Bracket

• Supplied Assembled with Square Nut
• Rolled Threads
• Square Shoulder
• Hot dip galvanized to meet ASTM A153

Carriage Bolt 1/2" x 5" J8645

The carriage bolts are roll threaded with square shoulder and square nut.

Carriage Bolt 1/2" x 6" J8646

The carriage bolts are roll threaded with square shoulder and square nut.

Carriage Bolt 1/2" x 8" J8648

The carriage bolts are roll threaded with square shoulder and square nut.

Carriage Bolt 3/8" x 4" J8634

The carriage bolts are roll threaded with square shoulder and square nut.
J834 Carriage Bolt: 3/8" x 4" (Thread Length: 3 ")

Carriage Bolt 3/8" x 4-1/2" J8634

The carriage bolts are roll threaded with square shoulder and square nut.

Carriage Bolt 3/8" x 5" J8635

Clevis Bolt 5/8" x 10" J7810

Clevis bolts are used to provide deadend connections to eyes or links. Clevis end includes 1/2" diameter machine bolt with nut and a stainless steel self locking cotter pin to provide a secure vibration proof assembly.

Clevis Bolt 5/8" x 12" J7812

Clevis bolts are used to provide deadend connections to eyes or links. Clevis end includes 1/2" diameter machine bolt with nut and a stainless steel self locking cotter pin to provide a secure vibration proof assembly.

Clevis Bolt 5/8" x 14" J7814

Clevis bolts are used to provide deadend connections to eyes or links. Clevis end includes 1/2" diameter machine bolt with nut and a stainless steel self locking cotter pin to provide a secure vibration proof assembly.

Double Arming Bolt 3/4" x 12" J8882

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 3/4" x 14" J8884

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 3/4" x 16" J8886

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 3/4" x 18" H J8888

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 3/4" x 20" J8890

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 3/4" x 22" H J8892

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 3/4" x 24" H J8894

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 3/4" x 26" H J8896

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 3/4" x 28" J8897

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 3/4" x 30" J8898

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 3/4" x 32" J8899

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 3/4" x 34" Allied Bolt 5998

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 3/4" x 36" Allied Bolt 5999

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 5/8" x 10" J8860

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts. Length dimensions do not include the points.

Double Arming Bolt 5/8" x 12" J8862

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts. Length dimensions do not include the points.

Double Arming Bolt 5/8" x 14" J8864

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 5/8" x 16" J8866

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 5/8" x 18" J8868

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 5/8" x 20" J8870

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 5/8" x 22" J8872

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 5/8" x 24" J8874

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 5/8" x 26" J8876

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 5/8" x 28" J8877

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 5/8" x 30" J8878

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 5/8" x 32" J8879

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 5/8" x 34" J8880

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Double Arming Bolt 5/8" x 36" J8881

Double Arming Bolt are roll threaded, with cone points at both ends for easy driving and removal without damage to threads. “D.A.” bolts are furnished with four square nuts.

Reinforce Brace 1-3/8" Allied Bolt 8001

Used to support the outer end of extension bolts when installing a parallel line to existing aerial plant.

• The distance between the Suspension Clamp and the above mounting hole is 8-3/4".
• Stock size is 1/8" x 1-3/8".
  
• Stamped from AISI 1018 steel.
  
• Hot dip galvanized to meet ASTM Specification B695.

Reinforcing Strap 1/8" x 1-3/4" J7905

Reinforcing Straps support the messenger bolt at locations of heavier than normal loading stress, such as long spans and are used with cable suspension clamps. The lower hole fits over the messenger bolt and the top end is fastened to the pole with a lag screw.

• Used in aerial construction as an added support for three-bolt suspension clamps.
• Stock size is .125 x 1-3/8".
• The distance between the Suspension Clamp and the above mounting hole is 5-7/8".
• Mounting hole diameters are both 11/16".
• Stamped from AISI 1018 steel.
• Hot dip galvanized to meet ASTM Specification B695.

Reinforcing Strap 1/8" x 2" J7908

Reinforcing Straps support the messenger bolt at locations of heavier than normal loading stress, such as long spans and are used with cable suspension clamps. The lower hole fits over the messenger bolt and the top end is fastened to the pole with a lag screw.

• Used in aerial construction as an added support for three-bolt suspension clamps.
• Stock size is .125" x 2".
• The distance between the Suspension Clamp and mounting hole is 5-7/8".
• Hole diameters are 11/16" and 25/32".
  
• Stamped from AISI 1018 steel.
  
• Hot dip galvanized to meet ASTM Specification B695.

Square Head Machine Bolt with Nut 1" X 16" Allied Bolt 8294

Used for fastening poleline hardware to crossarms, poles, and other structures.

• Has a formed "cone point" to ease attachment of nut.
• Allied Bolt marking (ABI) appears on the head of each bolt.
• Hot dip galvanized to meet ASTM Specification F2329.
• Supplied with attached square nut.
• Minimum tensile strength: 36,350 lbf.
• Recommended torque value: 314 ft lb.
• Minimum thread length is 6".
• Material conforms to ASTM specification A307.
• Dimensions conform to ASME B18.2.1.

Square Head Machine Bolt with Nut 1" X 18" 8297

Used for fastening poleline hardware to crossarms, poles, and other structures.

• Has a formed "cone point" to ease attachment of nut.
  
• Allied Bolt marking (AB) appears on the head of each bolt.
  
• Hot dip galvanized to meet ASTM Specification A153.
  
• Supplied with attached square nut.
  
• Minimum tensile strength: 36,350 lbf.
  
• Recommended torque value: 314 ft lb.
• Minimum thread length is 6".

Machine Bolt Square Head 1" X 18" H-8297

Square Head Machine Bolt with Nut 1/2" X 10" J8710

Used for fastening poleline hardware to crossarms, poles, and other structures.

• Has a formed "cone point" to ease attachment of nut.
• Allied Bolt marking (ABI) appears on the head of each bolt.
• Hot dip galvanized to meet ASTM Specification F2329.
• Supplied with attached square nut.
• Minimum tensile strength: 8,500 lbf.
• Recommended torque value: 37 ft lb.
• Minimum thread length is 6".
• Material conforms to ASTM specification A307.
• Dimensions conform to ASME B18.2.1.

Square Head Machine Bolt with Nut 1/2" X 12"J8712

Used for fastening poleline hardware to crossarms, poles, and other structures.

• Has a formed "cone point" to ease attachment of nut.
• Allied Bolt marking (ABI) appears on the head of each bolt.
• Hot dip galvanized to meet ASTM Specification F2329.
• Supplied with attached square nut.
• Minimum tensile strength: 8,500 lbf.
• Recommended torque value: 37 ft lb.
• Minimum thread length is 6".
• Material conforms to ASTM specification A307.
• Dimensions conform to ASME B18.2.1.

Square Head Machine Bolt with Nut 1/2" X 14" J8714

Used for fastening poleline hardware to crossarms, poles, and other structures.

• Has a formed "cone point" to ease attachment of nut.
• Allied Bolt marking (ABI) appears on the head of each bolt.
• Hot dip galvanized to meet ASTM Specification F2329.
• Supplied with attached square nut.
• Minimum tensile strength: 8,500 lbf.
• Recommended torque value: 37 ft lb.
• Minimum thread length is 6".
• Material conforms to ASTM specification A307.
• Dimensions conform to ASME B18.2.1.

Machine Bolt Square Head 1/2" X 14" H-8714

Square Head Machine Bolt with Nut 1/2" X 16"J8716

Used for fastening poleline hardware to crossarms, poles, and other structures.

• Has a formed "cone point" to ease attachment of nut.
• Allied Bolt marking (ABI) appears on the head of each bolt.
• Hot dip galvanized to meet ASTM Specification F2329.
• Supplied with attached square nut.
• Minimum tensile strength: 8,500 lbf.
• Recommended torque value: 37 ft lb.
• Minimum thread length is 6".
• Material conforms to ASTM specification A307.
• Dimensions conform to ASME B18.2.1.

Machine Bolt Square Head 1/2" X 16" H-8716

Square Head Machine Bolt with Nut 1/2" X 6" J8706

Used for fastening poleline hardware to crossarms, poles, and other structures.

• Has a formed "cone point" to ease attachment of nut.
• Allied Bolt marking (ABI) appears on the head of each bolt.
• Hot dip galvanized to meet ASTM Specification F2329.
• Supplied with attached square nut.
• Minimum tensile strength: 8,500 lbf.
• Recommended torque value: 37 ft lb.
• Minimum thread length is 6".
• Material conforms to ASTM specification A307.
• Dimensions conform to ASME B18.2.1.

Square Head Machine Bolt with Nut 1/2" X 8" J8708

• Has a formed "cone point" to ease attachment of nut.
• Allied Bolt marking (ABI) appears on the head of each bolt.
• Hot dip galvanized to meet ASTM Specification F2329.
• Supplied with attached square nut.
• Minimum tensile strength: 8,500 lbf.
• Recommended torque value: 37 ft lb.
• Minimum thread length is 6".
• Material conforms to ASTM specification A307.
• Dimensions conform to ASME B18.2.1.

Square Head Machine Bolt with Nut 3/4" x 10" MSI J8910

Used for fastening poleline hardware to crossarms, poles, and other structures.

• Has a formed "cone point" to ease attachment of nut.
• Allied Bolt marking (ABI) appears on the head of each bolt.
• Hot dip galvanized to meet ASTM Specification F2329.
• Supplied with attached square nut.
• Minimum tensile strength: 20,050 lbf.
• Recommended torque value: 130 ft lb.
• Minimum thread length is 6".
• Material conforms to ASTM specification A307.
• Dimensions conform to ASME B18.2.1.

Allied Bolt 8240 3/4" x 10" Square Head Machine Bolt with Nut