Cross Plate Anchor 3/4" J3520
MSI H-J3520 Cross Plate Anchor
- Made for the installation in holes augered by power drillers
- One piece formed anchors with wings and a base
- Retainer on the bottom hold the nut from the forged eye rod
- Hole Size: 20"
- Area ( Sq. In.): 250
- Rod Size: 5/8" or 3/4"
Big-Grip Dead-end 5/8" PLP BG-2111
Big-Grip Dead-ends are designed for use on Transmission, Antenna, Communications, and other types of guyed structures that require use of large guy strand.
Color Code: Black
Length: 64 Inch
Strand Size: 5/8"
Strand Construction 7W or 19W
Holding Straight 42,400 - 40,200
Big-Grip Dead-end 9/16" PLP BG-2116
Big-Grip Dead-ends are designed for use on Transmission, Antenna, Communications, and other types of guyed structures that require use of large guy strand.
Color Code: Yellow
Length: 55 Inch
Strand Size: 9/16"
Strand Construction 7W or 19W
Holding Straight 35,000
DEADEND BRACKET SF-YDB
ROLLER ASSEMBLIES ON EACH SIDE. 2" X 3/8 X 40-3/4 WITH 11/16 HOLE EACH SIDE 20.38 LONG USED FOR DEAD-END APPLICATIONS WITH WIRE FORMS OR STRAND VISE ON OPPOSING SIDES OF POLES YOKE or DEADEND BRACKET SF-YDB
Safety Guy-Wire Dispenser 14 AWG PLP SGD-0700
Preform Line Products Safety guy-wire dispenser is designed to provide safe, easy, completely controlled handling and paying-out of strand coils up to 500 ft in length, including EHS strand. It also can be used with wire, wire rope, cable, conductor, etc. Eliminate weight lifting, handling struggle, and the hazards of "runaway" coil ends. Small and light in weight (a carton of 50 weighs only 22 pounds), the safety guy-wire dispenser occupies minimal truck space. No banding or taping of coils is necessary. Saves personnel cost (only one person to pay out a loaded coil) and reduces inventory (just one universal size). Coil Not Included*
5/16" Steel Guy Wire, Strandvise,, Universal Grade .270-.315 MSI 5201
MSI 5201 5/16" Strand Vise, Universal Grade (Black)
- Primary Strand Size: 5/16"
- Wire Range: .270 - .315
- Overall Length (A): 10.69"
- Cartridge Width (B): 5.38"
- Bail Width (C): 1.63"
- Bail Type: A
- Used for deadend applications with overhead or down guy wire
- Rated to minimum of 90% of RBS of the Strand Vise
- Color Indicator for easy identification
- Recommended for use with Alumoweld, EHS, aluminized & galvanized steel strand
3/8" Steel Guy Wire, Strandvise, Universal Grade .325-.392 MSI 5202
MSI 5202 3/8" Strand Vise, Universal Grade (Orange)
- Primary Strand Size: 3/8"
- Wire Range: .325 - .392
- Overall Length (A): 12.88"
- Cartridge Length (B): 6.47"
- Bail Width (C): 1.63"
- Bail Type: A
- Used for deadend applications with overhead or down guy wire
- Rated to minimum of 90% of RBS of the Strand Vise
- Color Indicator for easy identification
- Recommended for use with Alumoweld, EHS, aluminized & galvanized steel strand
6-1/2" Wedge Clamp Conductor .250"-.414" MSI 7187
MSI H-7187, 6-1/2" Wedge Clamp, is mechanical holding device used for strain relief in service applications. It has solid stainless bails that are used on eye hooks and insulators with a diameter larger than 1.5". This clamp is designed for low tension applications only, and also has a mechanical working load of 1,200 lbs.
Specifications/Applications:
- Bail Size: 6-1/2"
- Material: Solid Stainless Steel
- Conductor Diameter Range: 0.250" - 0.414"
- ACSR ASTM-B232: 1/0 - #4
- AAAC ASTM-B399: 1/0 - #4
- AAC ASTM-B231: 2/0 - #2
Manta Ray Load Locker Setting Bar Adapter LL-1ASB 50132
The Manta Ray load locker Manta Ray LL-1 is required to load lock and proof test the anchor. It is a double acting hollow hydraulic jack with a base reaction plate and a direct reading gauge. The load locker can be used with the same hydraulic from the line truck used to drive the jack hammer.The LL-1 uses quick release gripping jaws that grip an Adapter Setting Bar (ASB) that passes through the
center of the jack. The ASB extends the anchor rod and precludes any damage to the anchor rod from the
gripping jaws.
Manta Ray Base Plate LL-3 50134 for LL1 Load Locker
The Manta Ray load locker Manta Ray LL-1 is required to load lock and proof test the anchor. It is a double acting hollow hydraulic jack with a base reaction plate and a direct reading gauge. The load locker can be used with the same hydraulic from the line truck used to drive the jack hammer.The LL-3(50134) Base Plate is designed for anchors that are installed at an angle to the ground. It has a large bearing surface and a small cross member.The vertical legs of the Base cut into the soil during use to help keep the base from skidding.For angled guy anchors the two cross members should be placed toward the tower and perpendicular to the axis of the anchor rod. *Base Plate Only
Manta Ray Drive Steel Extension Piece 33" SG-2 50233
Manta Ray 50233 SG-2, a 33" Drive Steel Extension is a
patented design made of high performance materials. It allows the anchor to be driven to depth in discrete increments
to allow installation in tight spaces while the operators remain safely on the ground. The anchor is threaded on both sides to accept a coupler for further length. The SG drive steel uses a partial left hand thread that allows very efficient impact energy transfer from the jack hammer
to the anchor. All joints should be lubricated with light oil or spray lubricant prior to assembly. After installing an anchor
the drive steel joints should be cleaned of dirt which will enter the couplers during driving. Failure to clean and lubricate
the drive steel and couplers will result in premature failure.
Manta Ray Radiused Drive Tip 30" SG-3 50236, for Drive Steel Set
Manta Ray 50236 SG-3, Radiused Drive Tip 30", this piece is shaped to fit into the anchor on one end and threaded on the other end to accept a coupler. The SG drive steel uses a partial left hand thread that allows very efficient impact energy transfer from the jack hammer
to the anchor. All joints should be lubricated with light oil or spray lubricant prior to assembly. After installing an anchor
the drive steel joints should be cleaned of dirt which will enter the couplers during driving. Failure to clean and lubricate
the drive steel and couplers will result in premature failure.
Bronze Vise Connector 1/4" MSI H-BVC-6
MSI H-BVC-6 Bronze Vise Connector
- Interlocking components ensure a
long term, vibration proof connection, one Piece, side opening design
eliminates loose parts, cross
threading, and eases installation on
run conductor
- Easy to install with gloves or hot sticks
- Connectors can be installed on
structures, cabinets and enclosures
- Conductor Range AWG: Max. #6 STR Min. #10 SOL
- Bolt Thread Size: 1/4"
- Bolt Hex. Size: 3/8"
Manta Ray Drive Steel Extractor Bar SG-X 50242
Manta Ray 50424 SG-X Drive Steel Extractor Bar is used in conjunction with the LL-1 Load Locker to extract any drive steel that happens to get stuck underground. Simply remove the hammer from the shank and screw the extractor bar (it also is rope threaded) into the coupler. Use the Load Locker to pull up on the “extractor bar” to break the drive steel free. Be careful as the drive steel is pulled out and removed to not allow portions of the drive steel to fall back down the hole. Usually there is some obstruction to removing the drive steel, and once they are broken free with the Load Locker they can easily be removed by hand.
Straight Suspension Clamp 5/8" MSI H-J25088.1
MSI H-J25088.1 5/8" Straight Suspension Clamp, with Flat Keeper Plate, is used with through bolts to serve as clamping member. This Flat 3-hole clamp securely grips messenger strand to pole, it uses a nut and square washer that is used between the clamp and pole for proper spacing.
Specifications:
- Firmly Grips 1/4" (6.6m) to 7/16" (16m) diameter messenger strand
- 3-Bolts,Flat
- Clamp Bolt Diameter: 1/2"
- Clamp Length: 5-3/4"
- Mounting Hole Diameter: 11/16" X 15/16"
- Constructed of high quality steel, hot-dipped galvanized
Curved Heavy Duty Suspension Clamp 5/8" MSI H-J7902B
MSI H-J7902B Curved Heavy Duty Suspension Clamp, is constructed with curved ends to prevent damage to the messenger strand when turning small angles. It is used in conjunction with through bolts to serve as clamping member, securely grips messenger strand to the pole. A nut and square washers are used between the clamp and pole to provide proper spacing.
Specifications:
- Firmly grips 1⁄4" (6.6M) to 7⁄16" (16M) diameter messenger strand
- Furnished with two track bolts and a center mounting hole
- constructed of high quality steel, hot-dipped galvanized
- Clamp Bolt Diameter: 5/8"
- Clamp Length: 6"
- Clamp Width: 2-3/16"
- Mounting Hole Diameter: 13/16"
Angled Thimble Eye Bolt 3/4" X 14" J8163
H-J8163 Angled 3/4" X 14" Thimble Eye Bolt, eliminates the need for thimble,shackles,links, and guy hooks.The broad
radius of the eye provides an excellent attachment point to deadend or guy messenger wire, guy strand for formed wire grips.
Specifications:
- Bolt Length: 14"
- Thread Length: 6"
- 20,050 lbs. minimum tensile strength
- Forged of high quality steel, hot-dip galvanized
5/8" X 20" OVAL EYE BOLT MSI H-J9420
MSI H-J9420 Oval Eye Bolt 5/8" X 20", is commonly used as an attachment point to secure thimbles, clevises, links, and deadend insulators.
Specifications:
- Forged, one-piece design
- Supplied assemble with square nut
- Eye I.D. : 1-1/2" width X 2" Length
- 13,550 lbs. minimum tensile strength
- Contructed of high quality steel, hot dip galvanized
Beam Clamp w/ Square Head MSI SI-2181
MSI SI-2181 Beam Clamp w/ Square Head, is used to provide an electrical connection to trailers, mobile homes or other beam structures. The cup point on bolt penetrates through surface paint or oxide for intimate ground to base metal.
Specifications:
- Seperate screws to attach #14 to #6 AWG ground wires
- High strength bronze casting
- UL & CUL Listed
- Bolt Head: Square
- Beam Ground Clamp
Structure Ground Clamp
Pair Straight/Half-Tap Modular 26-24 Gauge H-3M710-TC1-25
H-3M710-TC1-25 Pair Straight/Half -Tap Modular with Solid Cap Splice Connectors
Straight/Half-Tap splice connectors permit the joining of two cables, 25 pairs at a time. They may also be used for rearranging and transferring cable without interrupting service.
Features:
- Connector Pair Count: 25
- Connector Type: Straight/Half-Tap
- Modular Type: 710
- 26-24 Gauge, 0.40/0.51mm (0.016/0.020 In.)
Pair Bridge Splice Connector 26-22 Gauge H-3M710-BC1-25
H-3M710-BC1-25 Pair Bridge Splice Connector Filled Module
Bridge connectors are used in conjunction with either straight-only connectors or straight/half-tap connectors to permit pluggable 3-way splices, 25 pairs at a time.
Features:
- Connector Pair Count: 25
- Connector Type: Bridge
- Modular Type: 710
- 26-22 Gauge,
0.40/0.65 mm (0.016/0.020 In.)
3M™ SLiC™ 3.6X19-FB Corning Optical Closure Aerial Kit w/Float Bond Rubber End
3M™ SLiC™ Aerial Closure has a floating bond and a rubber end seal that ensures a snug fit for cables while eliminating
the need for drip collars. This 1-piece, dual-wall, molded closure is designed for construction or maintenance situations
3M SLiC Aerial Closure has a floating bond and interlocking ends that expand to meet a sheath opening of any size
without the use of any special kits. The 1-piece construction of this closure provides complete splice access after
placement and without the removal of the closure or the bonding from a cable.
Serving Sleeve 1/4" Hubbell 6452
Hubbell 6452 Serving Sleeve, for 1/4" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.
Specifications:
- Coating: Galvanized, ASTM A-153
- Material: Steel
- Length: 1.38"
Serving Sleeve 5/16" Hubbell 6453
Hubbell 6453 Serving Sleeve, for 5/16" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.
Specifications:
- Coating: Galvanized, ASTM A-153
- Material: Steel
- Length: 1.50"
Serving Sleeve 3/8" Hubbell 6454
Hubbell 6454 Serving Sleeve, for 3/8" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.
Specifications:
- Coating: Galvanized, ASTM A-153
- Material: Steel
- Length: 1.75"
Serving Sleeve 7/16" Hubbell 6455
Hubbell 6455 Serving Sleeve, for 7/16" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.
Specifications:
- Coating: Galvanized, ASTM A-153
- Material: Steel
- Length: 2.00"
Serving Sleeve 1/2" Hubbell 6456
Hubbell 6456 Serving Sleeve, for 1/2" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.
Specifications:
- Coating: Galvanized, ASTM A-153
- Material: Steel
- Length: 2.25"
Double Span Steel Brace Cross-arm 72" H-J1512
H-J1512 Brace, Cross-arm, Span 72", Drop 22"
One piece, angle steel, double span braces are used to support heavy cross-arm construction. Braces are attached to the underside of the cross-arm with 1/2" bolts or lag screws and fastened to the pole with a 5/8" bolt. The pole mounting section is designed to allow more than ample clearance for wrenching.
Specifications:
- Angle Size: 1-3/4" X 1-3/4" X 3/16"
- Span: 72"
- Drop: 22"
- Working Load: 1500 lbs.
- Pole mounting section designed to allow ample clearance for wrenching
- steel Hot dip galvanized
Single Upset Spool Bolt 5/8" X 14" MP J2348-1/2
Single Upset Spool Bolt 5/8" X 14" MP J2348-1/2 Minimum TENSILE STRENGTH 13,550 LBS
H-J2348-1/2 Single Upset Spool Bolt
- Shank Length: 14"
- Overall Length: 18-1/2"
- Thread Length: 6"
- Used for side-of-pole installation
when supporting neutral conductors
and secondary service wires
- Forged with either a single or double
integral washer upset at insulator end
- Double upset provide 15⁄8" clearance
between insulator and pole
- Spool bolts have 5⁄8" rolled threads
- Constructed of high quality steel,
hot-dip galvanized
- Use With H- J151 spool type insulator.
Angled Thimble Eye Bolt 3/4" X 10" J8161
Eliminates the need for thimbles, shackles, links and guy hooks
The broad radius of the eye provides an excellent attachment point to deadend or guy messenger wire, guy strand or formed wire grips
Forged of high quality steel, hot-dip galvanized
- Minimum thread length is 4".
- Recommended torque value: 130 ft lb.
- Minimum Tensile Strength: 20,050 lbf.
10" Expanding Anchor For 5/8" or 3/4" Rod J8200-3/4/ALL19023
H-J8200-3/4/ALL19023 Burst Anchor Rod
- Hole Size: 10"
- Area (Sq. In.): 200
- Rod Size: 5/8" & 3/4"
- Made for installation in holes augered by power driller
- One-piece formed anchors with wings and a base
- Retainer on the bottom holds the nut from the forged eye nut from the forged eye rod
Double-Arming Bolt 3/4" X 10" J8883/ALL5977
Double-Arming Bolt 3/4" x 10"
Washer Head Lag Studs are used for light-duty mounting of cable hangers and cable suspension clamps. Stud end is manufactured with a forged square washer head and a roll threaded stud with assembled square nut. Lag end has sharp rolled gimlet threads and a cone point.
- Used to secure two cable suspension clamps or other attachments on opposite sides of utility pole.
- Each Double Arming Bolt is supplied with four attached square nuts.
- Bolt provided with cone point at each end to ease starting.
- Hot dip galvanized to meet ASTM Specification F2329.
- Minimum tensile strength: 20,050 lbf.
- Recommended torque value: 130 ft lb.
Our Price: $3.96
SALE Price: $3.08
You save $0.88!
6" Expanding Anchor For 1/2" or 5/8" Rod J0870
H-J0870 Bust Anchor Expanding 6"
- Hole Size: 6"
- Area (Sq. In.): 70"
- Rod Size: 5/8"
- Made for installation in holes augered by power drillers
- One piece formed anchors with wing and a base
- Retainer on the bottom holds the nut from the forged eye rod
PLP FIBERLIGN® Lite Support for ADSS .550" - .579" 4800115
The Preformed Line Products FIBERLIGN Lite Support (FLS) system is designed to
gently but firmly support All Dielectric Self-Supporting
(ADSS) cable. It is intended for tangent support installations (see “LINE ANGLES”) on lines that feature low
voltages, very short spans and low mechanical loads. For
products with higher capabilities see the subsequent pages
under FIBERLIGN® Dielectric Support, FIBERLIGN
Aluminum Support, FIBERLIGN Aluminum Suspension,
with and without rods and FIBERLIGN Dielectric
Suspension. The two latter products can be used in higher
voltage environments where track resistant ADSS cables.
Cable Diameter:
- Minimum: .550" (14 mm)
- Maximum: .579" (14.7 mm)
Safety Guy-Wire Jumbo Dispenser 12 AWG PLP SGD-0701
Preform Line Products Safety guy-wire dispenser is designed to provide safe, easy, completely controlled handling and paying-out of strand coils up to 500 ft in length, including EHS strand. It also can be used with wire, wire rope, cable, conductor, etc. Eliminate weight lifting, handling struggle, and the hazards of "runaway" coil ends. Small and light in weight (a carton of 50 weighs only 22 pounds), the safety guy-wire dispenser occupies minimal truck space. No banding or taping of coils is necessary. Saves personnel cost (only one person to pay out a loaded coil) and reduces inventory (just one universal size). Coil not included*
Square Head Machine Bolt 5/8 X 30 H-J8830
H-J8830 5/8 X 30 Square Head Machine Bolt
- Size: 5/8" X 30"
- Contracted of high quality steel, hot-dip galvanized
- Come points permit easy driving without damage to threads
- Bolts are supplied with one square nut assembled
- 13,550 lbs. minimum tensile strength
Milwaukee 48-22-9213 Lineman's High-Leverage Ratcheting Wrench
Lineman's High-Leverage Ratcheting Wrench features the most durable ratchet. The ratcheting wrench has a built-in strike face available in both milled and smooth, providing you with a dedicated surface for hammering. These wrenches are constructed from durable forged steel for longer tool life. The high leverage wrench fits 3/4", 1", and 1-1/8" square hardware.
Crossover Clamp for 1/4" Strand H-4069
H-4069 Crossover Clamp for 1/4" Strand
- Used in aerial construction at the mid-span to clamp two 1/4" strands together perpendicularly
- Crossover plates are tapped to eliminate the handling of loose nuts
- Stamped from AISI 1008 Steel
*10" TWIN SOLID SQUARE HUB HELIX POWER DRIVEN ANCHOR 1-1/2" HUB - 6000 FT. LB. FOR 3/4" AND 1" RODS H-D2104
- Installation is performed using a power digger. An anchor wrench fits over the square hub and a torque measurement device is required to determine proper installation.
- Correct installation is achieved only when the anchor is installed using the appropriate torque for the particular soil and anchor type.
- Installation torque is usually measured using a device connected in series with the wrench, digger, and Kelley Bar during installation.
Angled Thimble Eye Bolt 3/4" X 12" J8162
H-J8162 Angled 3/4" X 12" Thimble Eye Bolt, Used for dead-ending and attaching guy wires to poles and crossarms. Eliminates the need for thimble,shackles,links, and guy hooks.The broad radius of the eye provides an excellent attachment point to deadend or guy messenger wire, guy strand for formed wire grips.
Specifications:
- Bolt Length: 12"
- Thread Length: 6"
- 20,050 lbs. minimum tensile strength
- Recommended torque value: 130ft lb.
- Forged of high quality steel, hot-dip galvanized
Angled Thimble Eye Bolt 3/4" X 16" J8164
H-J8164 Angled 3/4" X 16" Thimble Eye Bolt, Used for dead-ending and attaching guy wires to poles and crossarms. Eliminates the need for thimble,shackles,links, and guy hooks.The broad radius of the eye provides an excellent attachment point to deadend or guy messenger wire, guy strand for formed wire grips.
Specifications:
- Bolt Length: 16"
- Thread Length: 6"
- 20,050 lbs. minimum tensile strength
- Recommended torque value: 130ft lb.
- Forged of high quality steel, hot-dip galvanized
Angled Thimble Eye Bolt 3/4" X 18" J8165
H-J8165 Angled 3/4" X 18" Thimble Eye Bolt, Used for dead-ending and attaching guy wires to poles and crossarms. Eliminates the need for thimble,shackles,links, and guy hooks.The broad radius of the eye provides an excellent attachment point to deadend or guy messenger wire, guy strand for formed wire grips.
Specifications:
- Bolt Length: 18"
- Thread Length: 6"
- 20,050 lbs. minimum tensile strength
- Recommended torque value: 130ft lb.
- Forged of high quality steel, hot-dip galvanized
GUY-GRIP® Dead-end 1/4" Light Application - "A" Coat GDE-1104LA
PLP GDE-1104LA 1/4" Dead-End Guy-Grip, Light Application - "A" Coat
- For use on extra-high-strength, high-strength, Siemens Martin, utilities-grade, galvanized steel strand, performance match Bezinal, GUY-GRIP dead-ends, false dead-ends and strand splices available.
- The Guy Grip is intended for use on single wood pole associated with distribution construction. They are made of the same material as the strand to which they are applied and are rated at 100% of the strands published rated breaking strength
- Size: 1/4"
- Mean Diameter: .259"
- Length: 25"
*8" TWIN SOLID SQUARE HUB HELIX POWER DRIVEN ANCHOR 1-1/2" HUB - 7000 FT. LB. FOR 3/4" AND 1" RODS H-D2847
- Installation is performed using a power digger. An anchor wrench fits over the square hub and a torque measurement device is required to determine proper installation.
- Correct installation is achieved only when the anchor is installed using the appropriate torque for the particular soil and anchor type.
- Installation torque is usually measured using a device connected in series with the wrench, digger, and Kelley Bar during installation.
Our Price: $133.54
SALE Price: $116.85
You save $16.69!
Joslyn Guy Clamp 2-Bolt 3/16" - 5/16" H-J926
SPECIAL ORDER
H-J926 Joslyn Guy Clamp 2-Bolt 3/16" - 5/16"
Joslyn Guy Clamps are rolled from carbon steel with straight parallel grooves that will not damage guy strand. Offset guy clamps are designed to give increase holding strength. The clamping bolts have special shoulders to prevent turning when the nuts are tightened,
Specifications:
- Number of Bolts: 2
- Bolt Diameter: 1/2"
- Clamping Length: 3-1/4"
- Clamp Width: 1-9/16"
- For Strand Diameter: 3/16" - 5/16"
Slingco TPE09682 Utility Pole Framing and Installation
Slingco makes utility pole framing and installation easier and more cost-effective than ever.
Slingco stores flat on any work vehicle and — with a few twists — transforms into the industry's most helpful device. Whether you're performing regularly scheduled pole replacement or if you're reacting to a natural disaster, Slingco gets the job done safer, faster and easy.
COMPACT: Folds to 3” x 23” x 30” for easy storage.
LIGHTWEIGHT: Only weighs 33 pounds.
STRONG: Supports poles from 30’ to 70’.
STABLE: Stays put on even and uneven ground.
Poleprop Utility Pole Framing
Communication Arm 3 & 2 Position Steel Under-build, 15° Angled WSO WB2751-B-HDG
HDG Communication Arm 3 & 2 - Position Steel Under-build, 15° Angled
15 degree angled Communication Arm 3 & 2 position Steel Under-build, galvanized for weather protection, and designed to allow for the addition of under-build cables. 36" & 24" in length from pole and 12" between mount holes.
All pole mounting and cable mounting holes are 11/16'' diameter.
WSO WB2751-B-HDG
3M™ SLiC™ 3.6x33SES Corning Optical Closure Aerial Kit w/Float Bond Spiral End
3M™ SLiC™ 3M™ SLiC™ Closures with Floating Bond and Spiral End Seal, 3M
Features fewer parts and easier installation with the 3M SLiC Aerial Closure, Superior seal, Easily adaptable, Single piece design, Double wall molded construction, Made from durable, rugged materials, Easy to access and reenter.
Additional Information
Standard Package Quantity: 1.0 each
Gross Weight: 5.8000 lbs