Condux 08914130 Fixed Head Innerduct Pulling Eye 1-1/4", 1.06" -1.43"
Tapered buttress threads thread into the innerduct for maximum pulling strength. These eyes connect directly to a Condux Swivel. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.
SUB - GMP60512

• Nominal Size: 1-1/4" (32 mm)
• Innerduct ID Range: 1.06" - 1.43" (27 - 37 mm)
• Max OD: 1.75" (44 mm)
• Hole Diameter: 0.38" (10 mm)
• Tang Thickness: 0.50" (13 mm)
• Tang Hole Diameter: 0.66" (17 mm)
• Tang Hole Location: 0.63" (16 mm)

Condux 08914140 Fixed Head Innerduct Pulling Eye 1-1/2", 1.37"-1.68"
Tapered buttress threads thread into the innerduct for maximum pulling strength. These eyes connect directly to a Condux Swivel. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.
SUB - GMP60515

• Nominal Size: 1-1/2" (38 mm)
• Innerduct ID Range: 1.37" - 1.68" (35 - 43 mm)
• Max OD: 2" (51 mm)
• Hole Diameter: 0.38" (10 mm)
• Tang Thickness: 0.50" (13 mm)
• Tang Hole Diameter: 0.66" (17 mm)
• Tang Hole Location: 0.63" (16 mm)

Condux 08914150 Fixed Head Innerduct Pulling Eye 1-3/4", 1.68"-1.81"
Tapered buttress threads thread into the innerduct for maximum pulling strength. These eyes connect directly to a Condux Swivel. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.
Specifications:

• Nominal Size: 1-3/4" (44 mm)
• Innerduct ID Range: 1.68" - 1.81" (43 - 46 mm)
• Max OD: 2.25" (57 mm)
• Hole Diameter: 0.38" (10 mm)
• Tang Thickness: 0.50" (13 mm)
• Tang Hole Diameter: 0.66" (17 mm)
• Tang Hole Location: 0.75" (19 mm)

Condux 08914160 Fixed Head Innerduct Pulling Eye 2", 1.93"-2.12"
Tapered buttress threads thread into the innerduct for maximum pulling strength. These eyes connect directly to a Condux Swivel. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.
SUB - GMP60520

• Nominal Size: 2" (51 mm)
• Innerduct ID Range: 1.93" - 2.12" (49 - 54 mm)
• Max OD: 2.50" (62 mm)
• Hole Diameter: 0.38" (10 mm)
• Tang Thickness: 0.50" (13 mm)
• Tang Hole Diameter: 0.81" (21 mm)
• Tang Hole Location: 0.75" (19 mm)

Condux 08914120 Fixed Head Innerduct Pulling Eye 1", 0.93"-1.06"
Tapered buttress threads thread into the innerduct for maximum pulling strength. These eyes connect directly to a Condux Swivel. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.
SUB - GMP60510

• Nominal Size: 1" (25 mm)
• Innerduct ID Range: 0.93" - 1.06" (24 - 27 mm)
• Max OD: 1.38" (35 mm)
• Hole Diameter: 0.25" (6 mm)
• Tang Thickness: 0.38" (10 mm)
• Tang Hole Diameter: 0.50" (13 mm)
• Tang Hole Location: 0.50" (13 mm)

Condux 08960712 Pulling Eye, Inner-Duct 1-1/4" Swivel Head

Condux 08960715 Pulling Eye, Inner-Duct 1.37" - 1.50" Swivel Head
The Inner-duct Pulling Eye is a hybrid tool that combines features from standard inner-duct pulling eyes and Condux swivels. A swivel head prevents twisting and binding of the inner-duct as it is installed. It eliminates the need for a separate swivel on each pulling eye when installing single innerducts into individual conduits or multiple inner-ducts into a single conduit. Its short length is an advantage on tight bends compared to using a separate swivel and pulling eye. Easily installed using a 1-3⁄8" deep socket or adjustable wrench.
SUB - GMP61515

Condux 08960720 Pulling Eye, Inner-Duct 2" Swivel Head
The Inner-duct Pulling Eye is a hybrid tool that combines features from standard inner-duct pulling eyes and Condux swivels. A swivel head prevents twisting and binding of the inner-duct as it is installed. It eliminates the need for a separate swivel on each pulling eye when installing single innerducts into individual conduits or multiple inner-ducts into a single conduit. Its short length is an advantage on tight bends compared to using a separate swivel and pulling eye. Easily installed using a 1-3⁄8" deep socket or adjustable wrench.
SUB - GMP61520

Offers a quick and easy way to connect pulling eyes or swivels to winch lines, harnesses or rope. To close, simply screw the nut onto the threaded end. Connectors are reusable.

Offers a quick and easy way to connect pulling eyes or swivels to winch lines, harnesses or rope. To close, simply screw the nut onto the threaded end. Connectors are reusable.

Offers a quick and easy way to connect pulling eyes or swivels to winch lines, harnesses or rope. To close, simply screw the nut onto the threaded end. Connectors are reusable.

Offers a quick and easy way to connect pulling eyes or swivels to winch lines, harnesses or rope. To close, simply screw the nut onto the threaded end. Connectors are reusable.

Offers a quick and easy way to connect pulling eyes or swivels to winch lines, harnesses or rope. To close, simply screw the nut onto the threaded end. Connectors are reusable.

Offers a quick and easy way to connect pulling eyes or swivels to winch lines, harnesses or rope. To close, simply screw the nut onto the threaded end. Connectors are reusable.

LEG CAPACITY: 650LBS
SLING CAPACITY: 2600LBS
Wire rope is 2600 lb total capacity to allow multiple pulls at one time by attaching 2, 3, or 4 cables or ducts to the puller. The slings are manufactured from aircraft quality wire rope. The various "legs" are staggered in length so that the individual connections are not interfering with each other. The lead coupler can be easily dismantled to change out a leg or add another leg. Each leg is marked with load capacity and they are pull tested 3 times that rating. The safety factor of 3:1 based on equal pull on all cables, (horizontal pull only). Yokes and wire rope sling legs may be ordered separately.
DCD-23125-040

Wire leg is 2300lb. total sling capacity 6900lb. to allow multiple pulls at one time by attaching 2, 3, or 4 cables or ducts to the puller. The slings are manufactured from aircraft quality wire rope. The various "legs" are staggered in length so that the individual connections are not interfering with each other. The lead coupler can be easily dismantled to change out a leg or add another leg. Each leg is marked with load capacity and they are pull tested 3 times that rating. The safety factor of 3:1 based on equal pull on all cables, (horizontal pull only). Yokes and wire rope sling legs may be ordered separately.
DCD-23250-030

Pulling eyes are designed with cutting edges to actually cut a thread in the bore of the ducting as it is....

Pulling eyes are designed with cutting edges to actually cut a thread in the bore of the ducting as it is....

Pulling eyes are designed with cutting edges to actually cut a thread in the bore of the ducting as it is....

Wire leg is 4800lb. total sling capacity 14400lb. to allow multiple pulls at one time by attaching 2, 3, or 4 cables or ducts to the puller. The slings are manufactured from aircraft quality wire rope. The various "legs" are staggered in length so that the individual connections are not interfering with each other. The lead coupler can be easily dismantled to change out a leg or add another leg. Each leg is marked with load capacity and they are pull tested 3 times that rating. The safety factor of 3:1 based on equal pull on all cables, (horizontal pull only). Yokes and wire rope sling legs may be ordered separately.
DCD-23375-030

LEG CAPACITY: 4800LBS
SLING CAPACITY: 19200 LBS
Wire rope SLING is 19200 lb total capacity to allow multiple pulls at one time by attaching 2, 3, or 4 cables or ducts to the puller. The slings are manufactured from aircraft quality wire rope. The various "legs" are staggered in length so that the individual connections are not interfering with each other. The lead coupler can be easily dismantled to change out a leg or add another leg. Each leg is marked with load capacity and they are pull tested 3 times that rating. The safety factor of 3:1 based on equal pull on all cables, (horizontal pull only). Yokes and wire rope sling legs may be ordered separately.
DCD-23375-040