Ground Hog EX3 3' Auger Extension
Auger Extension 3' GROU-EX3, Ground Hog offers a large range of augers and accessories for our earthdrills to cover all types of soil conditions and customer requirements.
Manta Ray 50132 LL-1ASB Adapter, Load Locker Setting Bar
The Manta Ray load locker Manta Ray LL-1 is required to load lock and proof test the anchor. It is a double acting hollow hydraulic jack with a base reaction plate and a direct reading gauge. The load locker can be used with the same hydraulic from the line truck used to drive the jack hammer.The LL-1 uses quick release gripping jaws that grip an Adapter Setting Bar (ASB) that passes through the
center of the jack. The ASB extends the anchor rod and precludes any damage to the anchor rod from the
Manta Ray 50242 SG-X Drive Steel Extractor Bar
Manta Ray 50424 SG-X Drive Steel Extractor Bar is used in conjunction with the LL-1 Load Locker to extract any drive steel that happens to get stuck underground. Simply remove the hammer from the shank and screw the extractor bar (it also is rope threaded) into the coupler. Use the Load Locker to pull up on the “extractor bar” to break the drive steel free. Be careful as the drive steel is pulled out and removed to not allow portions of the drive steel to fall back down the hole. Usually there is some obstruction to removing the drive steel, and once they are broken free with the Load Locker they can easily be removed by hand.
Ground Hog SD12 Standard 12" X 3' Auger for Earth Drill
The Ground Hog SD12 Standard Auger has a standard-style digging head for loose/sandy soil condition. This 12" Auger uses a screw-in fishtail centered pilot and bolt-on wide flat, hardfaced, standard side blades. All Ground Hog Augers are approximately
38"(3') in length and utilize a 7/8" standard square drive for interchangeability between Earth Drills.
- Part #100 Fishtail Pilot(1)
- Part #912 Side Blade Installed(1)
- Part #1300 Attachment Pin & Clips(1)
- 7//8" Square Drive for interchangeability
- Durable Powder-Coated Finished
- 12" hole diameter
Ground Hog PSD8 Pengo-Style 8" X 3' Auger for Earth Drill
The Ground Hog PSD8 Pengo 8" Auger features heat treated cast alloy steel boring heads with hardened forged steel side blades and a bolt-on cast alloy steel centered pilot bit. The Pengo Series augers are general purpose augers and are the best choice for tough soil conditions. All Ground Hog Augers are approximately 38"(3') in length and utilize a 7/8" standard square drive for interchangeability between Earth Drills.
- Part # SB-25 Pilot Bit(1)
- Part # 35 Side Blades Installed(2)
- Part # 1300 Attachment Pin & Chip
- 8" hole diameter
- 7//8" Square Drive for interchangeability
- Screw-in hardfaced alloy steel pilot bit
- Durable Powder-Coated Finish
- Replaceable Forged Steel Side Blades
Manta Ray 50233 SG-2 33" Drive Steel Extension Piece
Manta Ray 50233 SG-2, a 33" Drive Steel Extension is a
patented design made of high performance materials. It allows the anchor to be driven to depth in discrete increments
to allow installation in tight spaces while the operators remain safely on the ground. The anchor is threaded on both sides to accept a coupler for further length. The SG drive steel uses a partial left hand thread that allows very efficient impact energy transfer from the jack hammer
to the anchor. All joints should be lubricated with light oil or spray lubricant prior to assembly. After installing an anchor
the drive steel joints should be cleaned of dirt which will enter the couplers during driving. Failure to clean and lubricate
the drive steel and couplers will result in premature failure.
Hydraulic Hose 25' With Flush HC16-25 *EACH*
*MUST BUY TWO*
/Hydraulic Hose EACH 25' ½” nominal size and 25’ length w/ HTMA flush face couplers. A maximum 50 ft hose length is recommended. 227.73 EACH. TWO ARE REQUIRED FOR MANTA RAY AND/OR POLE PULLER
Manta Ray 50134 LL-3 Base Plate for LL1 Load Locker
The Manta Ray load locker Manta Ray LL-1 is required to load lock and proof test the anchor. It is a double acting hollow hydraulic jack with a base reaction plate and a direct reading gauge. The load locker can be used with the same hydraulic from the line truck used to drive the jack hammer.The LL-3(50134) Base Plate is designed for anchors that are installed at an angle to the ground. It has a large bearing surface and a small cross member.The vertical legs of the Base cut into the soil during use to help keep the base from skidding.For angled guy anchors the two cross members should be placed toward the tower and perpendicular to the axis of the anchor rod. *Base Plate Only
Kelly Bar 2.5/8 Hex Adapter HUB 630012HD
To determine which Kelly Bar Adapter you need first measure your Kelly Bar across the flats for the correct Kelly Bar Adapter size. Then determine the maximum torque possible from the Digger motor to choose the correct Kelly Bar Adapter.Two torque ratings are available,10,000 and 15,000 ft-lbs. 18 pounds.
Kelly Bar 2.5 Hex Adapter HUB 630011HD
To determine which Kelly Bar Adapter you need first measure your Kelly Bar across the flats for the correct Kelly Bar Adapter size. Then determine the maximum torque possible from the Digger motor to choose the correct Kelly Bar Adapter.Two torque ratings are available,10,000 and 15,000 ft-lbs.
No-Wrench Anchor Tool \ Anchor Adapter HUB-E3030255
Especially designed for use with the Chance portable anchor
installer. This tool bolts directly to the installer's output flange or
Kelly bar adapter having six 1/2" dia. holes on a 5-1/4" bolt circle.
Adjustable pivoting plates accept rods from 3/4" to 1-1/4" diameter.
For manually-installed foundations, eyenut must be temporarily
installed for installation. Has four holes on 5-1/4" bolt circle for
attachment. Includes four 1/2" x 1-1/2" bolts, nuts and lockwashers.
Locking Dog Assembly HUB C3030069HD
6 1/2" BOLT 5 1/4 CENTER This is an attachment and goes with the Kelly Bar Drive End Wrench and the Kelly Bar Adapter to install anchors. The Locking dog weighs 20 pounds and is 7 inches high. C3030069HD
Kelly Bar 1 3/8 Hex Drive End Wrench HUB-C1021583
This is one of the two drive end wrenches for the complete tool system for installing anchors made by A.B. Chance. This bar is 57 pounds and is 7 feet tall. Standard Drive-End Wrench installs 8,000 ft.-lb. (sma4,000 ft.-lb. Standard-Strength PISA anchors,ll hub) Tough One ® anchors,10,000 ft.-lb. (small hub) TougOne® anchors,6,000 ft.-lb. Mid-Strength PISA anchors. Fits 1-3/8 solid & 2.25" socket drive
Kelly Bar 1 1/2 Drive End Wrench HUB C3031064
This is one of the two drive end wrenches for the complete tool system for installing anchors made by A.B. Chance. This bar is 67 pounds and is 7 feet tall. Large Hub Fits 1-1/2 solid & 2.5" socket drive
inside dimension 1.54 Outside dimension 2.44
Ground Hog Earth Drill C-71-5H
The C-71-5H Earth Drill is the work-horse of the Ground Hog line, tried and tested for over 30 years. Also known as an " Anchor Drill". This is a two man drill. Auger Bits sold separately.
MANTA LL-2 LOAD LOCKER
Light Duty Hand Pump.The LL-2 Anchor Locking kit is designed to Load Lock and proof test Small Manta Ray
and Duckbill anchors. It is manually operated and has a maximum capacity of 8000
pounds (36kN). It can accommodate anchors installed vertically or at angle to the
ground. The anchor capacity is easily read on the included gauge. The design of the LL-2
is such that the load on the anchor in pounds is equal to the pressure in psi (pounds per
square inch) as read on the gauge. It includes an accessory kit to allow attachment to
anchors equipped with SAR-58 style anchor rods, AT-16 (1/2” UNC) or AT-12 (3/8”
UNC) anchor rods, or cabled anchors. The kit also includes a Rod Clamp and cable sling
accessory to allow gripping of SAR-58 Style anchors below the ends of the threads.
MANTA LB-1 50093 Kit Complete Hydraulic Auger
Little Beaver The LB-1 kit consist of:
- HDL-210 Two man handle with 10 cu" displace Hydraulic motor 200 RPM.
- 9092-M one piece Torque Tube, short.
- 9054-4X36 Extension, Snap-on, 4X36.
- 4X42-SSC Auger, Snap-on, Carbide Point.
- 9093-A Torque Tube Bracket, Wiggle Joint for NPTT, incl. Mounting Bolts.
- 9027 Point, Standard.
- 3012-2 Bolt, HEX NC, 3/8 X 1 pltd GR 5.
- 9027-KEP, Nut, KEP NC, 3/8 pltd. (Nut w/ Lock Washer)
- 9023-4, Blade, 4 inches.
- 9024, Bolt Hex NC, 1/4 X 7/8 pltd. GR 5.
- 9026-KEP, Nut, KEP NC, 1/4 pltd. (Nut w/ Lock Washer)
- 9023-C4RT, Blade, Carbide 4" Ripper Teeth.
- Requires a Hydraulic Power Pack or truck with a Hydraulic Tool Circuit
MANTA RAY Load Locker KIT 50127, Hydraulic Control Valve and Plate LL-1
- The Manta Ray load locker Manta Ray LL-1 is required to load lock and
proof test the anchor. It is a double acting hollow hydraulic jack with a base
reaction plate and a direct reading gauge. The load locker can be used with the
same hydraulic from the line truck used to drive the jack hammer.The base plate
is designed for anchors that are installed at an angle to the ground. It has a
large bearing surface and a small cross member. For angled guy anchors the two
cross members should be placed toward the tower and perpendicular to the axis
of the anchor rod. The kit includes the Manta LL-1FPM 50141 (10) Ton Load Locker, Manta LL-3 50134 Base Plate, Manta LL-1FPM Homak 32in. Industrial Steel Storage box ,Manta LL-1ASB 50132 Adapter Load Locker Setting Bar, Manta LL-1TJ 50148 Tapered Jaw set, 5/32 Hex Driver 51188 (For adjustment of the Bypass Valve on LL-1FPM) and Manual.
MANTA HB-90 50364 STANLEY HYDRAULIC JACKHAMMER [1-1/4 inch]
The Stanley BR87 Hydraulic Jack Hammer is a heavy duty tool for work in the 90 pound
class and above for 8+" Mata Ray Installation, & concrete applications. It is highly
productive in utility construction, street maintenance,
repair of water and gas mains, and general contracting
A feathering on/off valve controls speed, making start up
and initial tool placement easy.
A diaphragm accumulator provides trouble free operation
and will handle system back pressures up to 250 psi (17
Operates on open center systems and is available in 1-1/8
or 1-1/4 inch chuck hex sizes.
MANTA STANLEYGPU 18-8 50382 HYDRAULIC POWER PACK
The GT18 hydraulic power unit AKA Hydraulic Power Pack is engineered for continuous
professional use and is optimized to deliver ideal flows and pressures to both
Type 1 and Type 2 hydraulic tools. Its powerful 18 HP Briggs & Stratton
engine and best-in-class cooling system deliver the power and heat rejection
pros need to keep tools working uninterrupted all day in all types of
conditions. The GT18 features a computerized all-electric throttle control
system that idles-down the engine when tools aren't running, saving fuel and extending
service life. Its feature-rich, dependable operation make the GT18 the
workhorse of the industry.
Manta Ray Utility Anchor System/R
Complete setup to drive a Manta Ray anchor into the ground. When pulled the Manta Ray will lock horizontally into the ground never coming loose. One of the best ways to assemble a down guy.