The GMP 08608 H Cable Block, is used to pull cable toward or away from corner poles and any other locations.
It takes cables of a diameter from 1-1/2" to 3" and is designed to endure the high stresses encountered when pulling the cable around corners of poles.It features a positive clamping mechanism that securely latches onto a strand allowing the sheave to tilt with lead without prematurely releasing it and has a 5,000 lbs load capacity. The sheave is enclosed in a forged, hinged steel frame.

Used with a 45° corner block, cable is supported as it comes off the reel and follows the path of the strand. The bracket is fabricated of 5/16" x 2" structural hot-rolled steel. The design is such that the bracket swivels freely under the strand clamp (not provided) effectively compensating for situations where the trailer cannot be set in line with the path of the strand.

USED

The Power End Plate Cutter provides a fast, convenient method of cutting precise cable access holes in end plates. Furnished standard with 26 blades from 0.375 in. to 3.50 in. in diameter, with four additional blades for larger sizes up to 4 in. available. Kit includes a cable measure tape for accurately measuring cable diameter and selecting correct blade size. Includes carrying case.

Epoxiglas Hook Ladders have many applications in high voltage maintenance to position linemen in the most advantageous working location.The hooks can be swiveled to best fit various angles on structure. Steel chains clip to hooks to assist in securing ladder to support. Meets ASTM F711 and IEC 61478 - Category 2
Length: 10'
Strength Rating: 1250 IB.

Detent "L" Handle Safety Locking Pin for Sherman Reilly 016-010-01 Crossarm Bracket.
Pin Diameter: 7/16"

MN21 12 volt batteries for GoLight series wireless remote controls. These batteries are used for all go light wireless remote controls. These include the Stryker handheld (GL-30100) and Dash Mount (GL-30200) wireless remote controllers, as well as the Radio-Ray
GL-7900T wireless remote. Includes 1 pair of batteries. Each remote takes 2 batteries.

The Golight 30100 wireless remote control can operate a Go Light up to 80 feet away.This remote can be used with all Go Lights (except GoBee 2151) that have wireless remote capabilities.The remote takes 1 pair of MN21 12 volt batteries.
*1 pair of batteries included

Extra separate 6 ft. extension pole. The popular FG Series of fiberglass poles by Jameson have been an industry standard for over 50 years. The high quality of these fiberglass poles makes them the preferred choice for telecommunication lineman, arborists and landscapers. These lay-up sticks offer a strong yet lightweight solution without sacrificing control or bending strength.

• Each hollow core fiberglass pole measures 1.25 in. outside diameter with a wall thickness of 0.125 in. and weigh just over 2 lbs.
• A polymer protective surface veil is utilized to prevent fiber blooming on the surface due to abrasion or ultraviolet light
• End ferrules are constructed from aircraft grade aluminum and feature an exterior leaf spring locking button to give you a secure connection when attaching poles or tools
• Poles are batch tested to 100 Kv/ft. for 5 minutes but are not intended for use as a hot stick
  

The Ground Hog SD12 Standard Auger has a standard-style digging head for loose/sandy soil condition. This 12" Auger uses a screw-in fishtail centered pilot and bolt-on wide flat, hardfaced, standard side blades. All Ground Hog Augers are approximately
38"(3') in length and utilize a 7/8" standard square drive for interchangeability between Earth Drills.
Feature:

• Part #100 Fishtail Pilot(1)
• Part #912 Side Blade Installed(1)
• Part #1300 Attachment Pin & Clips(1)
• 7//8" Square Drive for interchangeability
• Durable Powder-Coated Finished
• 12" hole diameter

The Ground Hog PSD8 Pengo 8" Auger features heat treated cast alloy steel boring heads with hardened forged steel side blades and a bolt-on cast alloy steel centered pilot bit. The Pengo Series augers are general purpose augers and are the best choice for tough soil conditions. All Ground Hog Augers are approximately 38"(3') in length and utilize a 7/8" standard square drive for interchangeability between Earth Drills.
Features:

• Part # SB-25 Pilot Bit(1)
• Part # 35 Side Blades Installed(2)
• Part # 1300 Attachment Pin & Chip
• 8" hole diameter
• 7//8" Square Drive for interchangeability
• Screw-in hardfaced alloy steel pilot bit
• Durable Powder-Coated Finish
• Replaceable Forged Steel Side Blades

MSI 5201 5/16" Strand Vise, Universal Grade (Black)

• Primary Strand Size: 5/16"
• Wire Range: .270 - .315
• Overall Length (A): 10.69"
• Cartridge Width (B): 5.38"
• Bail Width (C): 1.63"
• Bail Type: A
• Used for deadend applications with overhead or down guy wire
• Rated to minimum of 90% of RBS of the Strand Vise
• Color Indicator for easy identification
• Recommended for use with Alumoweld, EHS, aluminized & galvanized steel strand

MSI 5202 3/8" Strand Vise, Universal Grade (Orange)

• Primary Strand Size: 3/8"
• Wire Range: .325 - .392
• Overall Length (A): 12.88"
• Cartridge Length (B): 6.47"
• Bail Width (C): 1.63"
• Bail Type: A
• Used for deadend applications with overhead or down guy wire
• Rated to minimum of 90% of RBS of the Strand Vise
• Color Indicator for easy identification
• Recommended for use with Alumoweld, EHS, aluminized & galvanized steel strand

MSI H-7187, 6-1/2" Wedge Clamp, is mechanical holding device used for strain relief in service applications. It has solid stainless bails that are used on eye hooks and insulators with a diameter larger than 1.5". This clamp is designed for low tension applications only, and also has a mechanical working load of 1,200 lbs.
Specifications/Applications:

• Bail Size: 6-1/2"
• Material: Solid Stainless Steel
• Conductor Diameter Range: 0.250" - 0.414"
• ACSR ASTM-B232: 1/0 - #4
• AAAC ASTM-B399: 1/0 - #4
• AAC ASTM-B231: 2/0 - #2

The Manta Ray load locker Manta Ray LL-1 is required to load lock and proof test the anchor. It is a double acting hollow hydraulic jack with a base reaction plate and a direct reading gauge. The load locker can be used with the same hydraulic from the line truck used to drive the jack hammer.The LL-1 uses quick release gripping jaws that grip an Adapter Setting Bar (ASB) that passes through the center of the jack. The ASB extends the anchor rod and precludes any damage to the anchor rod from the gripping jaws.

The Manta Ray load locker Manta Ray LL-1 is required to load lock and proof test the anchor. It is a double acting hollow hydraulic jack with a base reaction plate and a direct reading gauge. The load locker can be used with the same hydraulic from the line truck used to drive the jack hammer.The LL-3(50134) Base Plate is designed for anchors that are installed at an angle to the ground. It has a large bearing surface and a small cross member.The vertical legs of the Base cut into the soil during use to help keep the base from skidding.For angled guy anchors the two cross members should be placed toward the tower and perpendicular to the axis of the anchor rod. *Base Plate Only

Manta Ray 50148 LL-1TJ Tapered Jaw Set, is a key component for LL-1 Load Locker. The Taper Jaw provides
grip to the Adapter Setting Bar which is pulls upward on the anchor rod and tips the anchor underground.
*Taper Jaw Only*

Manta Ray 50233 SG-2, a 33" Drive Steel Extension is a
patented design made of high performance materials. It allows the anchor to be driven to depth in discrete increments
to allow installation in tight spaces while the operators remain safely on the ground. The anchor is threaded on both sides to accept a coupler for further length. The SG drive steel uses a partial left hand thread that allows very efficient impact energy transfer from the jack hammer
to the anchor. All joints should be lubricated with light oil or spray lubricant prior to assembly. After installing an anchor
the drive steel joints should be cleaned of dirt which will enter the couplers during driving. Failure to clean and lubricate
the drive steel and couplers will result in premature failure.

Manta Ray 50236 SG-3, Radiused Drive Tip 30", this piece is shaped to fit into the anchor on one end and threaded on the other end to accept a coupler. The SG drive steel uses a partial left hand thread that allows very efficient impact energy transfer from the jack hammer
to the anchor. All joints should be lubricated with light oil or spray lubricant prior to assembly. After installing an anchor
the drive steel joints should be cleaned of dirt which will enter the couplers during driving. Failure to clean and lubricate
the drive steel and couplers will result in premature failure.

Manta Ray 50424 SG-X Drive Steel Extractor Bar is used in conjunction with the LL-1 Load Locker to extract any drive steel that happens to get stuck underground. Simply remove the hammer from the shank and screw the extractor bar (it also is rope threaded) into the coupler. Use the Load Locker to pull up on the “extractor bar” to break the drive steel free. Be careful as the drive steel is pulled out and removed to not allow portions of the drive steel to fall back down the hole. Usually there is some obstruction to removing the drive steel, and once they are broken free with the Load Locker they can easily be removed by hand.

Condux 08017200 Breakaway Swivel 5/8" 600 lbs.
Essential for fiber optic and coaxial cable pulling, these swivels have a break load ranging from 150–1,800 pounds (667–8,006 N) and are designed to separate at ±10% of their rated break load. If the load rating is exceeded, the interior break pin fractures, the swivel separates, and the cable remains undamaged.
Size: 5/8"
Specifications:
Length: 3.56" (90mm)
Diameter: 0.625" (16mm)
Entire Slot Depth: 0.79" (20mm)
Pin Center: 0.37" (9mm)
Pin Diameter: 0.25" (6mm)
Slot Width: 0.28" (7mm)
Break Load (Underground): 600 lbs. (2669 N)
Break Load (Aerial): 360 lbs (1601.36 N)

Klein 63324 Steel Handle Bolt Cutter 24", an all purpose, center-cut jaws for soft, medium, and hard metals. Forged, alloy tool steel jaws are precision ground for sure, efficient cutting and long life. The red steel handles have heavy vinyl grips ends for 90 degree cuts.
Specifications:

• Soft & Medium cutting max capacity: 7/16" (11.1 mm)
• Hard Material Cutting 5/16" max capacity: 5/16" (7.9 mm)
• Handle Material: Steel
• Handle Color: Red
• Replacement Blade: # 63824
• Overall Length: 24" (609.6 mm)

Klein 85076 7 Piece Cushion Grip Screwdriver Set
This 7-Piece Klein Tools Screwdriver Set contains the most frequently used, general purpose screwdrivers. Included are three cabinet-tip, two Phillips-tip, and two keystone-tip style screwdrivers. Each screwdriver features Klein's patented Tip-Ident which allows quick identification of the type of screwdriver and tip orientation.
Specifications:

• General purpose selection of the most frequently used screwdrivers
• Includes: Three cabinet-tip, two Philips-tip, and two Keystone-tip styles
• Cushion-grip handle for smooth feel and corrosion resistance
• Internal flanges inside handle provide solid, twist resistant blade anchor
• Special heat-treated shafts
• Precision-machined tip for exact fit
• Meets or exceeds applicable ASME/ANST specifiactions
• Tip-indent quickly identifies the screw driver type and up orientation

Sherman Reilly 7832 Urethane Lined Sheave with Ground 22"
Sherman + Reilly urethane-lined aluminum sheaves are made identically to polished-groove sheaves (above) except that a premium-grade polyurethane lining is cast-in-place on the sheaves’ conductor-contact surface. The properties of the urethane and casting it in place on the bare sheave together assure a high-precision profile of the lined sheave. The urethane’s formulation assures resiliency to cushion conductors, as well as assures hardness, high load-bearing capacity, impact resistance, abrasion resistance, resistance to compression-set, and resistance to oil, ozone, and other environmentals – all of which contribute to long useful life, even under harsh field conditions. A-scale durometer hardness of the lining is 90-92. SOLD AS ONE EA.

Specifications/Features:

• Size: 22"
• Sheave OD: 22"
• Rim Width: 3-1/8
• Maximum Working Load: 12,000 lbs.
• Ground Bottom Diameter: Polished Groove: 18", Lined: 18-1/8"
• Groove Radius: 13/16"
• High Strength & Weight
• High Efficiency, Low Friction
• Polished Groove/ Urethane

Sherman Reilly XS-100B-DI Universal Stringing Block with Ductile Iron
The XS-100B’s light weight and durability derive from the materials and methods used to make it. The material used for the frame is “virgin” A356-T6 aluminum, which is an aluminum alloy with very tightly controlled proportions of other materials to assure optimum performance during manufacture and in the field. Virgin material is material that has not been mixed with scrap material, not even with scrap of what may have once been the same alloy. The fact that Sherman + Reilly uses “virgin” material assures that the material is exactly and only the pure and correct alloy, and that it has not been contaminated by impurities (notably iron) that often accompany non-virgin material.
Specifiactions:

• High Strength, Low weight
• Positive Locking Handle ( a secure spring loaded latch and large-ID pull-loop) on the side gate assembly for easy conductor clip-in and for hot-stick operations
• high-efficiency, Low Friction
• Maximum Working Load; 2500 lbs.
• Efficiency: 98%
• Maximum Conductor OD: 1-3/4"
• Sheave OD:7"
• Sheave Groove Radius: 1"
• Sheave Throat Width: 3-3/16"
• Sheave Rim Width; 3"
• Overall Width: 7"
• Overall Height: 14-11/16" with bracket
• Overall Height: 15-13/16" without bracket
• Frame Material; A356-T6 Aluminum (Virgin)
• Sheave Material: Ductile Iron
• Hanging Hardware: Socket Connector

Sherman Reilly XS-100B-U Universal Stringing Block with Urethane Lined Sheave
Sherman & Reilly urethane-lined aluminum sheaves are made identically to polished-groove sheaves (above) except that a premium-grade polyurethane lining is cast-in-place on the sheaves’ conductor-contact surface. The properties of the urethane and casting it in place on the bare sheave together assure a high-precision profile of the lined sheave. The urethane’s formulation assures resiliency to cushion conductors, as well as assures hardness, high load-bearing capacity, impact resistance, abrasion resistance, resistance to compression-set, and resistance to oil, ozone, and other environmentals – all of which contribute to long useful life, even under harsh field conditions. A-scale durometer hardness of the lining is 90-92. Blocks with urethane-lined sheaves are especially appropriate for stringing conductor, static wire, and fiber optic cables. However, they typically cost ~ 25% more than polished groove.
Specifications:

• Height Strength, Low Weight
• Positive Locking handle ( a secure spring loaded latch and large-ID Pull-Loop) on the side gate assembly for easy conductor clip-in and for easy conductor clip-in and for hot-stick operations
• Maximum Working Load; 2500 lbs.
• Efficiency: 98%
• Maximum Conductor OD: 1-3/4"
• Sheave OD:7"
• Sheave Groove Radius: 1"
• Sheave Throat Width: 3-3/16"
• Sheave Rim Width; 3"
• Overall Width: 7"
• Overall Height: 14-11/16" with bracket
• Overall Height: 15-13/16" without bracket
• Frame Material; A356-T6 Aluminum (Virgin)
• Sheave Material: Ductile Iron
• Sheave Lining: Urethane
• Hanging Hardware: Socket Connector

Bashlin 76PAT Patriot Wood Pole Fall Restraint Device 6" - 20"
The Patriot is here to free you from the tyranny and restrictions of other WPFRD's

• It is lightweight, at least 20% lighter than competitive product
• Ergonomic approved design reduces upper body strength
• Allows proper body position and leg placement when climbing
• 76PAT, 6" - 20" Pole Diameter

Bashlin 76PAT-T Patriot Wood Pole Fall Restriction Device - Transmission Model 6" - 30" Dia.
The Patriot is here to free you from the tyranny and restrictions of other WPFRD's.

• It is lightweight, at least 20% lighter than competitive product
• Ergonomics approved design reduces upper body strength
• Allows proper body position and leg placement when climbing a pole
• 76PAT-T, 6" - 20" Pole Diameter

H-J2348-1/2 Single Upset Spool Bolt

• Shank Length: 14"
• Overall Length: 18-1/2"
• Thread Length: 6"
• Used for side-of-pole installation when supporting neutral conductors and secondary service wires
• Forged with either a single or double integral washer upset at insulator end
• Double upset provide 15⁄8" clearance between insulator and pole
• Spool bolts have 5⁄8" rolled threads
• Constructed of high quality steel, hot-dip galvanized

GMP 71500 Sierra Cable Lasher
The Sierra Cable Lasher is recommended for new construction to lash a single aerial cable or numerous cables to supporting strand with stainless steel lashing wire.
Specifications/Features:

• Uses our full size industry-standard annealed stainless steel coils of lashing wire available in diameters from .038" - .065"
• Single lashes cables and wires from drop wire size up to 1.9" (50 mm) maximum outside diameter
• Lashes on strand sizes down as small as 3/16" (5 mm) all the way up to 1/2" (12 mm)
• The Lasher drum makes one revolution for every 13" (33 cm) of travel leaving the wire helically wound around the strand/cable(s) bundle creating one support per revolution
• Made from high-quality materials and precision machined just like its bigger brothers, the SIERRA Lasher is ideal for lashing smaller wire and cables where a bigger machine is too much
• The Sierra Lasher can be pulled equally as easy from below or from directly ahead
• With a like design, most parts are interchangeable with the Cable Spinning Model 5-500M Lasher
• Overall Size: 15 X 10 X 10" (38 X 25 X 25 cm)
• Weighs 19 lbs. without wire

MSI J8161 Angled Thimble-Eye Bolt

• Bolt Length: 10"
• Thread Length: 4"
• Eliminates the need for thimbles, shackles, link, and guy hooks
• The broad radius of the eye provides an excellent attachment point to dead-end or guy messenger wire, guy strand or formed wire grips
• 20,050 Lbs. minimum tensile strength
• Forged of high quality steel, hot-dip galvanized

IGLOO 00025041, Wire Truck Rack for 2-5 gallon Water Jugs
Keep your coolers strapped down in the back of the truck with the igloo Wire Truck Rack.
Specifications/Features:

• Fits 2-5 gallon Igloo beverage coolers, including 5-gallon roller
• Heavy duty metal wire construction with welded joints for durability
• Treated surface with stands tough outdoor conditions
• Durable, adjustable webbed cinch strap metal buckle firmly holds cooler in place
• Positions coder at the perfect height for easy height for easy access
• Exterior Dimension: 14.56" X 11.06' X 10.81" (36.99 cm x 28.1 cm x 27.46 cm)

IGLOO 385-431 400 Series Water Cooler 3 gallons
Specifications/Features:

• Ultratherm® insulation for maximum cold retention and maintains ice for up to 3 days in temperatures as high as 90°F
• HDPE hide won't chip, peel, buckle, or rust
• UV stabilizers prevent fading, cracking in all exposures
• Front push-button spigot is drip-resistant
• White FDA Grade liner is easy-to-clean and resists stains and odors
• Wide mouth pressure fit lid for easy filling
• Keeper cord prevents lid loss
• Color: Yellow/Red
• Material: Plastic
• Type: Insulated Water Cooler
• Height: 14"
• Width: 13-1/2"

IGLOO 384-451 400 Series Water Cooler 5 Gallons
Specifications/Features:

• Ultratherm® insulation for maximum cold retention and maintains ice for up to 3 days in temperatures as high as 90°F
• HDPE hide won't chip, peel, buckle, or rust
• UV stabilizers prevent fading, cracking in all exposures
• Front push-button spigot is drip-resistant
• White FDA Grade liner is easy-to-clean and resists stains and odors
• Wide mouth pressure fit lid for easy filling
• Keeper cord prevents lid loss
• Color: Yellow/Red
• Material: Plastic
• Type: Insulated Water Cooler
• Height: 20.38"
• Length: 14-1/2"
• Width: 13"

IGLOO 384-421 400 Series Water Cooler 2 Gallons
Specifications/Features:

• Ultratherm® insulation for maximum cold retention and maintains ice for up to 3 days in temperatures as high as 90°F
• HDPE hide won't chip, peel, buckle, or rust
• UV stabilizers prevent fading, cracking in all exposures
• Front push-button spigot is drip-resistant
• White FDA Grade liner is easy-to-clean and resists stains and odors
• Wide mouth pressure fit lid for easy filling
• Keeper cord prevents lid loss
• Color: Yellow/Red
• Material: Plastic
• Type: Insulated Water Cooler
• Height: 14-3/4"
• Length: 11-1/2"
• Width: 11.13"

GMP 71669 Reel Buck 50", 1200 lbs.
A tough, easily maneuvered and portable frame that's ideal for supporting a reel up to 50" (1270 mm) diameter.

• Two welded, rectangular steel members make up the frame.
• Designed for one-person.
• Will accommodates the Corning FlexNap cable reels.
• The frame is protected with a durable powder coat finish to prevent corrosion.
• Spindle bar included

• Max. Width: 36" (914 mm)
• Max. Drum: 50" (1270 mm)
• 42" Spindle Bar
• Load Capacity: 1200 lbs. (544 kg)
• Weight: 80 lbs. (36 kg)

GMP 71678 Reel Buck 50" 1200 lbs.
A tough, easily maneuvered and portable frame that's ideal for supporting a reel up to 50" (1270 mm) diameter.

• Two welded, rectangular steel members make up the frame
• Designed for one person
• Will accommodate the Corning FlexNap cable reels
• The frame is protected with a durable powder coat finish to prevent corrosion.
• Spindle bar included

• Max, Width: 54" (1372 mm)
• Max. Drum: 50" (1270 mm)
• 60" Spindle Bar
• Load Capacity: 1200 lbs. (544 kg)
• Weight: 90 lbs. (41 kg)

GMP 71679 Reel Buck 84", 500 lbs.
A tough, easily maneuvered and portable frame that's ideal for supporting any reel up to 84" (2134 mm)
diameter .

• Two welded, rectangular steel members make up the frame.
• Designed for one person.
• Will accommodate the Corning FlexNap cable reels.
• The frame is protected with a durable powder coat finish to prevent corrosion.
• Spindle bar included.

• Max. Width: 54" (1372 mm)
• Max. Drum: 84" (2134 mm)
• 60" Spindle Bar
• Load Capacity: 500 lbs. (227 kg)
• Weight: 100 lbs. (45 kg)

MILWAUKEE® M18 FUEL™ 7/16” Quick-Release Hex Utility High Torque Impact Wrench w/ ONE-KEY KIT™ delivers the Fastest Drilling Speed, More Power, and is Built for Maximum Control. The POWERSTATE™ Brushless Motor and all-new mechanism provide linemen with 30% faster drilling speeds, increasing your productivity while on the job. With up to 750ft-lbs max torque, this battery powered impact wrench gives you more power for effortless removal of rusted or corroded hardware. It is ergonomically designed for the lineman, providing you with superior control whether in-bucket, on-ground or climbing. The extended handle offers you increased grip surface, perfectly fitting high voltage safety gloves for improved comfort, less fatigue, and balanced maneuverability. This is the first 7/16” high torque impact gun in the industry to be equipped with a QUIK-LOK™ chuck, uniquely providing faster and easier bit changes. You can keep one hand firmly on the tool’s handle while inserting augers, sockets and other essential power utility accessories. The integrated lanyard loop allows you to easily transfer and store the tool. REDLINK PLUS™ Intelligence ensures maximum performance and protects your impact from overloads, heating, and over-discharge. The REDLITHIUM™ Battery Pack is compatible with 175+ M18™ tools, delivering you with more work per charge and more work over the life of the pack than competitors. With ONE-KEY™, you also gain the ability to Customize, Track and Manage your utility impact. ONE-KEY™ technology also allows you to save up to 4 task settings directly to the tool. If your tool is ever lost or stolen, its tracking functionality can lock it out.
Includes:

• (1) M18 Fuel 7/16" Hex Utility High Torque Impact Wrench w/ One Key (Tool Only) (2865-22)
• (2) M18 Red-Lithium XC5.0 Extended Capacity Battery Pack (48-11-1850)
• (1) M18 & M12 Multi-Voltage Charger (48-59-1812)
• Contractor Bag
• Inverter

• Voltage: 18v
• Length: 8.19"
• Width: 3.13"
• Height: 10.5"
• Weight: 5.85 lbs.
• Battery System: M18
• Power Source: Cordless

Hubbell 630013 Standard Kelly Bar Adapter 10,000 Ft Lbs (13,558 N-M) for 2" (50.8 mm) Hex Kelly Bar

• Kelly Bar Adapter attaches to truck's torque motor drive shaft (Kelly Bar)
• Locking Dog Assembly has six holes for 1/2" bolts on a 5-1/4" bolt circle comes with six 1/2" Grade 5 bolts, nut and lock washers
• Painted with green paint
• Bolt Grade: 5
• Kelly Bar Shape: Hex
• Number of Bolts Holes: 6
• Torque Rating: 10,000' lbs
• Type: Anchor/Pile Installation Tools

• Anchor Installation Hole Size: 0.5"
• Diameter - Bolt: 0.5"
• Diameter - Bolt Circle: 5.25"
• Kelly Bar Adapter Inside Width: 2"
• Kelly Bar Hole Distance to Flange: 5"
• Length: 6.125"
• Weight: 9.80 lbs.

GMP 10505 Super G Large Capacity Cable Lasher
The newest and largest of the GMP Lashers, this unit is designed to lash a large single or a combination of aerial cable to a supporting strand. It can be used for new installs or with existing cable in place.
Specs/Features:

• Lashes cable from about 2-1/2" to 5-1/4" outside diameter or multiple cables up to 5-3/4" combined outside diameter
• Lashes on strand from 11/32" to 1/2' diameter with one or two spiral wrappings of .061" or .065" diameter stainless steel wire
• Nominal spacing between wraps is approximately 18-19" (46 to 48 cm)
• Parallel-pull capability overcomes most terrain obstacles
• Wire tension constant regardless of amount on spool
• front rollers guide cables through the machine
• All smooth edges throughout help protect against cable damage
• Ergonomics design makes it easy to handle
• Each lasher includes a 6' bridle rope assembly with snap hooks, an information and operation manual and a heavy duty storage chest
• Comes with 2 extra reels for easy loading in the field
• Lasher weight: 58 lbs. without case or wire

Sherman Reilly 600941 7432 Urethane Lined Sheave with Ground 16"
Sherman + Reilly urethane-lined aluminum sheaves are made identically to polished-groove sheaves (above) except that a premium-grade polyurethane lining is cast-in-place on the sheaves’ conductor-contact surface. The properties of the urethane and casting it in place on the bare sheave together assure a high-precision profile of the lined sheave. The urethane’s formulation assures resiliency to cushion conductors, as well as assures hardness, high load-bearing capacity, impact resistance, abrasion resistance, resistance to compression-set, and resistance to oil, ozone, and other environmentals – all of which contribute to long useful life, even under harsh field conditions. A-scale durometer hardness of the lining is 90-92.
Specifications/Features:

• Size: 16"
• Sheave OD: 16-1/2"
• Rim Width: 2-1/4
• Maximum Working Load: 9,000 lbs.
• Ground Bottom Diameter: Polished Groove: 14", Lined: 14"
• Groove Radius: 23/32"
• Steel Socket Connector
• Safety Locking Headpin
• Built-in handle & hand line hook
• Lightweight Aluminum Alloy Sheave

Sherman Reilly 700407 Urethane Lined Sheave 16"
Sherman + Reilly urethane-lined aluminum sheaves are made identically to polished-groove sheaves (above) except that a premium-grade polyurethane lining is cast-in-place on the sheaves’ conductor-contact surface. The properties of the urethane and casting it in place on the bare sheave together assure a high-precision profile of the lined sheave. The urethane’s formulation assures resiliency to cushion conductors, as well as assures hardness, high load-bearing capacity, impact resistance, abrasion resistance, resistance to compression-set, and resistance to oil, ozone, and other environmentals – all of which contribute to long useful life, even under harsh field conditions. A-scale durometer hardness of the lining is 90-92.
Specifications/Features:

Sherman Reilly 74 series 700279 12" High Strength Aluminum Stringing Block
The 74 series single conductor stringing block is used mostly for new-line construction. It offers a conductor guard, which is an integral part of the aluminum alloy frame. This allows for the conductor to only come in contact with smooth aluminum surfaces. Should the conductor or pulling line come out of the sheave groove, the smooth contoured conductor guards will guide it back into the sheave groove. This virtually eliminates the chance of the conductor, pulling line, or pilot line, wedging between the sheave and the side frame.
Specification:

• Outside Sheave Diameter: 12"
• Rim Width: 2"
• Bottom Groove Diameter: PG2: 9-5/8" , Other3: 9-7/8"
• Point of Connection to bottom of groove: 8-15/16"
• Throat - Height: 4-13/16" , Width: 2-1/4"
• Overall Length: 20-3/8"
• Max Outside Width: 4-1/3"
• Radius Bottom Groove: 19/32"
• Max Working Load: 6,500 lbs.

Sherman Reilly 74 series 700775 14" High Strength Aluminum Stringing Block
The 74 series single conductor stringing block is used mostly for new-line construction. It offers a conductor guard, which is an integral part of the aluminum alloy frame.This allows for the conductor to only come in contact with smooth aluminum surfaces. Should the conductor or pulling line come out of the sheave groove, the smooth contoured conductor guards will guide it back into the sheave groove.This virtually eliminates the chance of the conductor, pulling line, or pilot line, wedging between the sheave and the side frame.
Specification:

• Outside Sheave Diameter: 14 1/2"
• Rim Width: 2 1/8"
• Bottom Groove Diameter: PG2: 12" , Other3: 9 1/2"
• Point of Connection to bottom of groove: 9-1/2"
• Throat - Height: 5-1/2" , Width: 2-3/8"
• Overall Length: 23-7/16"
• Max Outside Width: 5-1/8"
• Radius Bottom Groove: 21/32"
• Max Working Load: 7,500 lbs.

Sherman Reilly 74 series 700654 10" High Strength Aluminum Stringing Block
The 74 series single conductor stringing block is used mostly for new-line construction. It offers a conductor guard, which is an integral part of the aluminum alloy frame. This allows for the conductor to only come in contact with smooth aluminum surfaces. Should the conductor or pulling line come out of the sheave groove, the smooth contoured conductor guards will guide it back into the sheave groove. This virtually eliminates the chance of the conductor, pulling line, or pilot line, wedging between the sheave and the side frame.
Specification:

• Outside Sheave Diameter: 10"
• Rim Width: 1-7/8"
• Bottom Groove Diameter: 7-11/16" - 7-15/16"
• Point of Connection to bottom of groove: 8 7/8"
• Throat - Height: 4 13/16" , Width: 2-1/8"
• Overall Length: 18-3/8"
• Max Outside Width: 4-1/4"
• Radius Bottom Groove: 17/32"
• Max Working Load: 6,500 lbs.

Sherman Reilly 74 series 700182 16" High Strength Aluminum Stringing Block
The 74 series single conductor stringing block is used mostly for new-line construction. It offers a conductor guard, which is an integral part of the aluminum alloy frame.This allows for the conductor to only come in contact with smooth aluminum surfaces. Should the conductor or pulling line come out of the sheave groove, the smooth contoured conductor guards will guide it back into the sheave groove.This virtually eliminates the chance of the conductor, pulling line, or pilot line, wedging between the sheave and the side frame.
Specification:

• Outside Sheave Diameter: 16 1/2"
• Rim Width: 2 1/4"
• Bottom Groove Diameter: PG2: 14"
• Point of Connection to bottom of groove: 9-5/9"
• Throat - Height: 5-9/16" , Width: 2-1/2"
• Overall Length: 25-3/8"
• Max Outside Width: 5-128"
• Radius Bottom Groove: 23/32"
• Max Working Load: 9,000 lbs.

FREE 2019 CALENDAR

Shank Size: 5/8" - Diameter: 9/16" - Twist Length: 4 1/2" - Overall Length: 7 1/2"

American Pneumatic tool tampers are available with a choice of three types of butts. This butt is a half moon shaped butt. Applications range from foundation and pavement repair to the installation of power and telephone poles.

6" diameter internally reinforced

3" diameter solid

The APT Model 131 Backfill Tamper is used for soil compaction, temporary filling of holes, ashphalt packing etc.

APT 5200 117 30# JACKHAMMER
1X4-1/4" PAVING BREAKER

This 30 lb class Paving Breaker is an ideal tool for light to medium demolition work as well as for use in confined areas. This lightweight tool will break up concrete floors, and can be used in any other type of general demolition work. The M117 is now equipped with the patented Automatic Ball Valve. (Pat. # 8,276,682 B2)

• New! Patented Automatic Ball Valve
• Drop forged steel handle
• Built-in automatic oiler
• Replaceable chuck bushing
• Rubber handle grips
• Latch type retainer
• Swivel hose connector with universal coupler
• Four bolt back head
• Noise reducing muffler available

Tough and dependable, the high performance Model 190 Paving Breaker or Jack Hammer is the most powerful tool American Pneumatic Tool makes. 1-1/8 Shank. It is designed for big jobs such as heavy demolition and concrete breaking. Since the Model 190 has the ability to penetrate the hardest concrete it is the choice for road building and foundation removal.The 190 is now equipped with the patented Automatic Ball Valve.

18HP Arnco Power Pack TM351. Can be used with the Manta Ray Utility Anchor System.

REFURBISHED

3 GROVE BELT CABLES 5MM-16MM [5/8] HD/MD VERSION SMALLER

AIR TRACK SEAL KIT ARN-1-400460

AIR HOUSING SEAL-OFF DISK PUCK ARN-1-900936

C00169 BAND IT TOOL.

Standard BAND-IT® Banding Tool. For use on band widths of 1/4" to 3/4". Comes with a spin handle retaining ring to keep parts intact.

• Tensions over 2,400 lbs of force and cuts off the tail of the clamp being formed
• Used to apply BAND-IT® Stainless Steel Band, Galvanized Carbon Steel Band, BAND-FAST®, general use band and miscellaneous strapping
• Drop forged tool with built in cutter
• Spring loaded gripper lever improves ease of use
• Blue epoxy powder coated finish resists corrosive elements