The GMP "SideWinder", Trailer Mounted Fiber Optic Puller

The Condux 08690055 Fiber Optic Cable Pullers W/ Chart Recorder Includes digital readout. consist of a hydraulic motor, variable
speed foot control, manual flow control valve for adjusting maximum speed and a manually
adjustable pressure relief valve for adjusting the ultimate pull tension.

REMOTE STAND & TOOL BOX ONLY-- SKU: 08675675 WEIGHT:2,500.00 LBS Fiber Optic Cable Puller Options: Condux 08690001 Fiber Optic Cable Puller Package Condux 08690055 Fiber Optic Cable Puller Package 3 With Chart Recorder

Condux Fiber Optic Cable Pullers consist of a hydraulic motor, variable speed foot control,
manual flow control valve for adjusting maximum speed and a manually adjustable pressure
relief valve for adjusting the ultimate pull tension. Does not include digital readout.

TUF-Lugger Lite Cable Puller The Fiber Cable puller is a simple, easy to use cable puller that is designed to accommodate industry standard sheaves of 9”, 12”, 30", or 40” diameter specifically intended for use with fiber optic cables requiring a minimum bend radius. The unit is powered by the TUF-Lugger Lite gas winch (41000-000) or by the TUF-Lugger Lite electric winch (41000-500), providing a gas or electric option as a simpler, lighter, less costly option than a typical hydraulic puller.
40" 660lbs at max force, 152ft/min at max speed
30" 880lbs at max force, 114ft/min at max speed
12" 2200lbs at max force, 45ft/min at max speed

Condux 08675700 Portable Hydraulic Power Pack 9HP (5.9 GPM @ 1800 PSI)
These portable power sources are matched perfectly to the power requirements of the Condux Fiber Optic Cable Puller and the Fiber Optic Cable Blower. Power source is a 9 HP (6.7 kW) Honda (gas), or a 16 HP (11.9 kW) Briggs & Stratton V-Twin Vanguard (gas) engine. Features electric start, large capacity hydraulic cooler, quick disconnects, low oil shut-off and 16" (406 mm) diameter pneumatic tires.
Specification:

• Hydraulic System: Open Center
• Frame Type: Two Wheel Mobile unit
• Length: 26.5" (673 mm)
• Width: 20.00" (508 mm)
• Height: 27.5" (698 mm)
• Weight: 143 lbs. (64.9 kg)
• Filtration: 10 Micron Return Line Canister Type
• Oil Cooler: Air to Oil
• Engine: Gas, Honda, 9 HP (6.7 kW) @ 3,600 RPM
• Fuel: 1.6 gallons/18.9 liters
• Hydraulic Oil: 5.0 gallons/18.9 liters

Slip Clutch Capstans from Condux are designed to mount directly on a bayonet style winch drive shaft. A factory preset torque limiter prevents pulling tensions from exceeding 400 pounds. If the preset load is reached, the capstan will "slip" and discontinue rotating. High strength aluminum and steel construction ensures product durability and cable protection.

Slip Clutch Capstans from Condux are designed to mount directly on a bayonet style winch drive shaft. A factory preset torque limiter prevents pulling tensions from exceeding 300 pounds. If the preset load is reached, the capstan will "slip" and discontinue rotating. High strength aluminum and steel construction ensures product durability and cable protection.

The 40" model is available with a 1000 lbs. torque limiter Due to their generous working surface diameters, either size capstan can be used as an end puller or a mid-assist. Multiple units can be used in series for extra long pulling situations to eliminate the need to figure-8 cable at a mid-point All units mount on any 2 7/16" standard winch drum shaft extension; either bayonet or pin-type mount available The built-in torque limiter will limit the tension on the fiber optic cable during the pulling operation.

The 40" model is available with a 600 lbs. torque limiter Due to their generous working surface diameters, either size capstan can be used as an end puller or a mid-assist. Multiple units can be used in series for extra long pulling situations to eliminate the need to figure-8 cable at a mid-point All units mount on any 2 7/16" standard winch drum shaft extension; either bayonet or pin-type mount available The built-in torque limiter will limit the tension on the fiber optic cable during the pulling operation.

The 32" model is available with a 1000 lbs. torque limiter Due to their generous working surface diameters, either size capstan can be used as an end puller or a mid-assist. Multiple units can be used in series for extra long pulling situations to eliminate the need to figure-8 cable at a mid-point All units mount on any 2 7/16" standard winch drum shaft extension; either bayonet or pin-type mount available The built-in torque limiter will limit the tension on the fiber optic cable during the pulling operation.

Condux offers several sizes of capstans that fit the Condux Fiber Optic Cable Puller. These bayonet style capstans are offered in 12" (305 mm), 30" (762 mm), 42" (1,067) and 50" (1,270 mm) diameters for a standard 27⁄16" diameter bayonet style shaft.

The 32" model is available with a 600 lbs. torque limiter Due to their generous working surface diameters, either size capstan can be used as an end puller or a mid-assist. Multiple units can be used in series for extra long pulling situations to eliminate the need to figure-8 cable at a mid-point All units mount on any 2 7/16" standard winch drum shaft extension; either bayonet or pin-type mount available The built-in torque limiter will limit the tension on the fiber optic cable during the pulling operation.

Condux Capstans are to conform to the many specifications to fiber optic cable available, and to offer more cable pulling capabilities. Diameter: 30" Flat With: 8" Max cable OD 1.25".

Condux offers several sizes of capstans that fit the Condux Fiber Optic Cable Puller. These bayonet style capstans are offered in 12" (305 mm), 30" (762 mm), 42" (1,067) and 50" (1,270 mm) diameters for a standard 27⁄16" diameter bayonet style shaft. Intended use is for pulling innerduct power, telephone or coaxial cables.

Condux Capstan Wheel 30" X 4" 08675230

Install the cable puller on the frame with no modifications necessary to the puller.
By design, the Pole Mounting Frame offers a secure hold on the cable puller both
vertically and horizontally for a worry-free pull. A special plug drives into wood
poles for added stability. Includes all mounting hardware.

The 08675115 Remote Mounting Stand allows positioning of the cable puller well away from the power source. Easy to set up, the unit is both sturdy and compact.
Features 2-1/2" (64mm) square mount to accommodate any Fiber Optic Cable Puller.

GMP 71679 Reel Buck 84", 500 lbs.
A tough, easily maneuvered and portable frame that's ideal for supporting any reel up to 84" (2134 mm)
diameter .

• Two welded, rectangular steel members make up the frame.
• Designed for one person.
• Will accommodate the Corning FlexNap cable reels.
• The frame is protected with a durable powder coat finish to prevent corrosion.
• Spindle bar included.

• Max. Width: 54" (1372 mm)
• Max. Drum: 84" (2134 mm)
• 60" Spindle Bar
• Load Capacity: 500 lbs. (227 kg)
• Weight: 100 lbs. (45 kg)

The Condux 08675908 Fiber Optic Cable Puller Hitch Mount attaches directly into a typical 2" (51 mm)
square Reese-type receiver and the cable puller mounts in a 21⁄2" (64 mm) square fixture. An adjustable
jack is included for added stability and height adjustment. Pulling loads must not exceed 800 lbs. (3,559 N).

GMP 71678 Reel Buck 50" 1200 lbs.
A tough, easily maneuvered and portable frame that's ideal for supporting a reel up to 50" (1270 mm) diameter.

• Two welded, rectangular steel members make up the frame
• Designed for one person
• Will accommodate the Corning FlexNap cable reels
• The frame is protected with a durable powder coat finish to prevent corrosion.
• Spindle bar included

• Max, Width: 54" (1372 mm)
• Max. Drum: 50" (1270 mm)
• 60" Spindle Bar
• Load Capacity: 1200 lbs. (544 kg)
• Weight: 90 lbs. (41 kg)

This general purpose capstan is used for a wide variety of pulling and hoisting applications. Cast from a high strength aluminum alloy for low weight . Will fit on any 2-7/16 in. (62 mm) diameter winch extension shaft equipped with a bayonet or pin type mount. The working surface is 7-1/4 in. diameter x 8 in. (184 mm x 200 mm) wide. The maximum allowable pull is 4000 lbs. (1814 kgs).

GMP 71669 Reel Buck 50", 1200 lbs.
A tough, easily maneuvered and portable frame that's ideal for supporting a reel up to 50" (1270 mm) diameter.

• Two welded, rectangular steel members make up the frame.
• Designed for one-person.
• Will accommodates the Corning FlexNap cable reels.
• The frame is protected with a durable powder coat finish to prevent corrosion.
• Spindle bar included

• Max. Width: 36" (914 mm)
• Max. Drum: 50" (1270 mm)
• 42" Spindle Bar
• Load Capacity: 1200 lbs. (544 kg)
• Weight: 80 lbs. (36 kg)

The Condux Fiber Optic Cable Puller has a square mounting post 21⁄2" (64
mm) x 21⁄2" (64 mm). A female mounting socket  is required for
stability during cable pulling operations.

The Condux Fiber Optic Cable Puller has a square mounting post 21⁄2" (64
mm) x 21⁄2" (64 mm). A female mounting socket  is required for
stability during cable pulling operations.

The Condux Fiber Optic Cable Puller has a square mounting post 21⁄2" (64
mm) x 21⁄2" (64 mm). A female mounting socket  is required for
stability during cable pulling operations.

This Strand Jig Puller is used to pull out cable prior to the lashing operation. The main body of the Puller is a rugged one-piece aluminum casting. Two hardened steel rollers are provided to ride on either 5/16" or 1/4" strand. When pull-out pressure is released, a brake automatically holds the Puller in position. Pull-out pressure releases the brake. For best results, attach the cables in a balanced manner. Lemco PR965