Drop Side Snatch Blocks, 1 Wheel, 4,000 lb, 3/8 in Cable, Shackle - 7339752

• Model 4099
• For Wire Rope
• Steel Shell with Steel Sheaves
• Drop-Forged Fittings
• 3" & 4-1/2" Blocks Have Bronze Self-Lubricating Bushings; 6" Have Grooved Bronze Bushings with Pressure Grease Lubrication
• Galvanized Finish
• Special Feature: the Bolt Cannot Be Lost When the Block is Opened
• Connections Are Easily Interchangeable
• Working Loads are Resultant Working Loads
• DO NOT EXCEED THE WORKING LOAD LIMIT

This Block is normally used for pulling in self support or prelashed cable and is mounted with either a B, C, D, E, or F Cable Block Frame at a pole. SOLD SEPARATLY
E Cable Block With Halo PRELASH ROLLER GMP 74055.

Cable Block Frames are used to support either the E Cable Block (GMP74055) or Self Support Cable Block (GMP70200) when pulling in prelashed or self support aerial cable.

Cable Block Frames are used to support either the E Cable Block (GMP74055) or Self Support Cable Block (GMP70200) when pulling in prelashed or self support aerial cable.

Cable Block Frames are used to support either the E Cable Block (GMP74055) or Self Support Cable Block (GMP70200) when pulling in prelashed or self support aerial cable. Application: Light inside corners (4 ft. to 8 ft. pulls)

Cable Block Frames are used to support either the E Cable Block (GMP74055) or Self Support Cable Block (GMP70200) when pulling in prelashed or self support aerial cable. Application: All Outside Corners (4 ft. to 50 ft. pulls)

This block is perfect for temporarily supporting any cable up to 2-3/4 in. (70 mm) diameter on 1/4 - 3/8". (6-10 mm) dia. suspension strand during new construction or while overlashing to existing lashed cable.

The GMP 08608 H Cable Block, is used to pull cable toward or away from corner poles and any other locations. It takes cables of a diameter from 1-1/2" to 3" and is designed to endure the high stresses encountered when pulling the cable around corners of poles. It features a positive clamping mechanism that securely latches onto a strand allowing the sheave to tilt with lead without prematurely releasing it and has a 5,000 lbs load capacity. The sheave is enclosed in a forged, hinged steel frame.

The GMP 79601 Modified E Cable Leader is 12 ft. (3.65m) long and consists of several
hinged weights which normally hang vertically to resist cable and strand
rotation. It also contains a tipper bar assembly (in the front) for
attaching the pulling-in rope sling and swivel, and a special tip
assembly for attaching a cable grip, replacing the provided strand grip.

This versatile, economical block supports any cable up to 1 1/4 in. (32mm) in diameter including coaxial, up so you can use it in CATV cabling

• There's a lifting ring for easy strand placement, a molded rubber roller for smooth motion, and a steel sleeve and shaft for durability

• The hot rolled steel frame is powder-coated for extra visibility and corrosion resistance

This block is functionally similar to the D cable block. This larger tool can be used with G cable lasher to handle cables up to 5". Features strand hooks up to accommodate 3/8 - 3/4 diameter strand. Contains to vertical side rollers, in addition to the sleeve, to minimize cable friction during pull-in.

This OVERLASH cable block is perfect for temporarily any cable up to 2 3/4 (70 mm) diameter on 1/4 - 3/8in (6-10 mm)diameter. Suspension strand during new construction or while over-lashing to existing lashed xable. Spring loaded keeper is to keep smaller cables captured in the pulley.

This block can support multiple cables during new strand construction. Can accommodate four 1" (25 mm) cables on nylon rollers. Locking gates keep cable(s) on the rollers.

The block is used to support up to 2¾" telephone, fiber or coaxial cable prior to the lashing operation. The frame and sheave are cast of aluminum. Also known as slap on roller, clip on, roller, fiber roller, overlash roller, coffin roller, overlash blocks, cable rollers. PY-750 - 1/4" strand.

Sherman Reilly Crossarm Bracket or Cross-Arm Bracket Quick Release Bracket allows for 5 block positions: 0, 22, 45, 68, and 90 degrees.6.5" high x 4.5" wide Xarm Bracket - Cross arm - Maclean

The 9511 block, or big little block, is little in overall length and weight but big in sheave and load capacity.
Side opening for ease in placing in hoisting line. Safety locking pin permits easy opening, positive locking and is captive to blocks,
no parts to drop or lose. Frame of high strength aluminum alloy, ribbed for extra strength and rigidity.
Integral guard prevents wedging of lines. Sheaves mounted on anti-friction ball bearings are available with polished aluminum,
neoprene lined, urethane lined, or ductile iron. Urethane lining recommended when wire rope hoisting lines are to be used.
Snatch Block

Designed for Overhead Ground Wires, Ideal for use with Transformer Gin
Size: 6"
Wire OD: 3/4"
Load capacity: 3,000 Ibs
Swivel safety Hook