Dura-line's Split Lock + is manufactured from a glass fiber that is reinforced with nylon resin. These heat and UV stabilized couplers provide an excellent impact strength. Conveniently reusable, making it ideal for temporarily coupling conduits, especially at slack-loop locations, as well as for air-assisted jetting applications. This coupler can be is easily assembled using a 7/16" nut driver.
Size: 1.25"

Sold 1 ea.

Dura-line's Split Lock + is manufactured from a glass fiber that is reinforced with nylon resin. These heat and UV stabilized couplers provide an excellent impact strength. Conveniently reusable, making it ideal for temporarily coupling conduits, especially at slack-loop locations, as well as for air-assisted jetting applications. This coupler can be is easily assembled using a 7/16" nut driver.
Size: 1.00"

Sold 1 ea.

Dura-line's Split Lock + is manufactured from a glass fiber that is reinforced with nylon resin. These heat and UV stabilized couplers provide an excellent impact strength. Conveniently reusable, making it ideal for temporarily coupling conduits, especially at slack-loop locations, as well as for air-assisted jetting applications. This coupler can be is easily assembled using a 7/16" nut driver.
Size: 1.50"

Sold 1 ea.

Condux 08078200 Foam Carrier, lightweight carrier easily blow through duct. Best suited for start runs and operates with with multiple bends.
Specifications:
Duct Size: 1/2" (13 mm)
Max. OD: 0.50" (13 mm)

Condux 08078300 Foam Carrier, lightweight carrier easily blows through duct. Best suited for shorrt runs and operates with multiple bends.
Specifications:

• Duct Size: 3/4" (19 mm)
• Max. OD: 0.75" (19 mm)

Condux 08676860, Speed Ball Insert Innerduct Split Coupling 1.25"

Used for temporary joining all types of innerduct during the cable blowing process.

*One Insert Set includes Rubber Seal*

Specifications:

• Nominal Duct Size: 1.25" (32 mm)
• Duct Type: 1 1/4" SDR 11, 13.5
• Mean Duct OD: 1.660" (42 mm)

Condux 08676861, Speed Ball Insert Innerduct Split Coupling 1.50"

Used for temporary joining all types of innerduct during the cable blowing process.

*One Insert Set includes Rubber Seal*

Specification:

• Nominal Duct Size: 1.50" (38 mm)
• Duct Type: 1-1/2" SDR 11, 13.5
• Mean Duct OD: 19.00" (48 mm)

Condux 08676863, Speed Ball Insert Innerduct Split Coupling 40mm

Used for temporary joining all types of innerduct during the cable blowing process.

*One Insert Set includes Rubber Seal*

Specification:

• Nominal Duct Size: 1.575" (40 mm)
• Duct Type: 40 mm
• Mean Duct OD: 1.575" (40 mm)

Condux 08676862, Speed Ball Insert Innerduct Split Coupling 2.00"

Used for temporary joining all types of innerduct during the cable blowing process.

*One Insert Set includes Rubber Seal*

Specifications:

• Nominal Duct Size: 2.00" (61 mm)
• Duct Type: 2.00" SDR 11, 13.5
• Mean Duct OD: 2.375" (60 mm)

Condux 08761439 Foam Carrier, this foam carrier is specially designed for spreading lubricant in duct prior to fiber optic cable blowing/jetting.
Specifications:

• Carrier Size: 1.25" (31.8 mm)
• Duct Range (Inside) Diameter: 1" SDR 13.5, 11 (25 - 22 mm)

Condux 08761440 Foam Carrier, is specially designed for spreading lubricant in duct prior to fiber-optic
cable blowing/jetting.
Specification:

• Carrier Size: 1.50" (38.1 mm)
• Duct Range (Inside) Diameter: 1.25" (30-39 mm) SDR 13.5", 11

Condux 08761441 Foam Carrier, is specially designed for spreading lubricant in duct prior
to fiber optic cable blowing/jetting.
Specifications:

• Carrier Size: 1.75" (44.5 mm)
• Duct Range (Inside) Diameter: 1.50" SDR 13.5, 11 (38 - 45 mm)

Condux 08676859, Speed Ball Insert Innerduct Split Coupling 1.00",

Used for temporary joining all types of innerduct during the cable blowing process.

*One Insert Set includes Rubber Seal*

Specifications:

• Nominal Size: 1.00" (25 mm)
• Duct Type: 1" SDR 11 & 13.5
• Mean Duct OD: 1.315" (33 mm)

Condux 08761442 Foam Carrier, is specially designed for spreading lubricant in duct prior
to fiber-optic cable blowing/jetting.
Specifications:

• Carrier Size: 2.00" (50.8 mm)
• Duct Range (Inside) Diameter: 2.00" SDR 13.5, 11 (46 - 52 mm)

Condux 08032600 Foam Carrier, lightweight carrier easily blow through duct. Best suited for start runs and operates with with multiple bends.
Specifications:
Duct Size: 4" (102 mm)
Max. OD: 4.00" (102 mm)

Condux 08032500 Foam Carrier, lightweight carrier easily blow through duct. Best suited for start runs and operates with with multiple bends.
Specifications:
Duct Size: 3" (76 mm)
Max. OD: 3.00" (76 mm)

Duraline 20001491, no heat or tools are needed. Simply push the duct ends into the coupler for a locked and air-sealed assembly.

B&C BC02-117R SIDR11.5 Plastic Reverse Thread 1" Coupler

• Fits Verizon Duct ID: 1.15-1.2" True SIDR11.5
• Size: 1"
• Color: Brown
• Material: Plastic

SPLIT PLASTIC COUPLER 2" CABTEC-PE2.375-2
The couplings are removable and lightweight, sealing completely to 200 lbs PSI and are guaranteed to handle tensile loads up to 600 lbs.
Reusable.

The couplings are removable and lightweight, sealing completely to 200 lbs PSI and are guaranteed to handle tensile loads up to 600 lbs.
Reusable.

The couplings are removable and lightweight, sealing completely to 200 lbs PSI and are guaranteed to handle tensile loads up to 600 lbs.
Reusable.

The couplings are removable and lightweight, sealing completely to 200 lbs PSI and are guaranteed to handle tensile loads up to 600 lbs.
Reusable.

This series of aluminum airtight couplings incorporates the same reliable, full circumference seal used in our barbed ring compression couplings. But unlike other one piece plastic or aluminum compression couplings that have to be installed with some type coupling press, These reverse threaded barbed ring couplings can be installed like any ordinary reverse thread coupling. Instead of a coupling press, a special wide pitch, fast traveling thread is used to force the innnerduct over barbed ring seal.
Sold individually.
SDR Duct Outer Diameter: 1.488

The sharp buttress type threads withstand high pulling loads that meet or exceed the Bellcore tensile standard of 1000 lbs. These coupling are machined with one degree of taper and have a long chamfered lead-in for straight, easy starting. The couplings incorporate a wide, eight pitch thread angle which greatly reduces the number of revolutions necessary to install the couplings. These versatile couplings can be used in manholes, direct bury, aerial, or any application except where an air or water tight connection is required..
Sold individually.
Smooth wall 2.345" Nom OD (in) Verizon 2" TRU SDR duct.

Cable-Tec ASB1.94 TRUESIDR11.5 Airtight Aluminum Coupling, Reversed Thread Barbed
O.D 1.194 This series of aluminum airtight couplings incorporates the same reliable,

full circumference seal used in our barbed ring compression couplings.

But unlike other one piece plastic or aluminum compression couplings

that have to be installed with some type coupling press,

these reverse threaded barbed ring couplings can be installed

like any ordinary reverse thread coupling. Instead of a coupling press,

a special wide pitch, fast traveling thread is used to force the innnerduct

over barbed ring seal. Sold individually.

DUCT OD 11.5-1 NOTTRUE SIDR1.220 ID FOR 1" DUCT Aluminum Coupler
This series of aluminum airtight couplings incorporates the same reliable, full circumference seal used in our barbed ring compression couplings. But unlike other one piece plastic or aluminum compression couplings that have to be installed with some type coupling press, these reverse threaded barbed ring couplings can be installed like any ordinary reverse thread coupling. Instead of a coupling press, a special wide pitch, fast traveling thread is used to force the innnerduct over barbed ring seal. Sold individually.

The original Condu-Grip provides a 100% long-term airtight and watertight seal for smooth wall PE conduit.....

The original Condu-Grip provides a 100% long-term airtight and watertight seal for smooth wall PE conduit....

The original Condu-Grip provides a 100% long-term airtight and watertight seal for smooth wall PE conduit....

The original Condu-Grip provides a 100% long-term airtight and watertight seal for smooth wall PE conduit....

Comfit Push Fit Push Lock is a unique Hi-Tech coupler for HDPE cable ducts. Leak tested at 230 PSI and resistant to corrosion and most ...

Comfit Push Fit Push Lock is a unique Hi-Tech coupler for HDPE cable ducts. Leak tested at 230 PSI and resistant to corrosion and most...

Comfit Push Fit Push Lock is a unique Hi-Tech coupler for HDPE cable ducts. Leak tested at 230 PSI and resistant to corrosion and most...

Comfit Push Fit Push Lock is a unique Hi-Tech coupler for HDPE cable ducts. Leak tested at 230 PSI and resistant to corrosion and most...

STRAIGHT CONNECTOR-5MM MICROFIT COUPLER Condux 08566310

Designed specifically for FTTx applications, the Condux® Microfit Couplers combine ease of use, chemical resistance and ability to accommodate the high pressures encountered when installing fiber with micro-blowing equipment.

STRAIGHT CONNECTOR-7MM MICROFIT COUPLER Condux 08566312

Designed specifically for FTTx applications, the Condux® Microfit Couplers combine ease of use, chemical resistance and ability to accommodate the high pressures encountered when installing fiber with micro-blowing equipment.

STRAIGHT CONNECTOR- 8MM MICROFIT COUPLER Condux 08566335

Designed specifically for FTTx applications, the Condux® Microfit Couplers combine ease of use, chemical resistance and ability to accommodate the high pressures encountered when installing fiber with micro-blowing equipment.

STRAIGHT CONNECTOR- 10MM MICROFIT COUPLER Condux 08566315

Designed specifically for FTTx applications, the Condux® Microfit Couplers combine ease of use, chemical resistance and ability to accommodate the high pressures encountered when installing fiber with micro-blowing equipment.

STRAIGHT CONNECTOR- 12MM MICROFIT COUPLER Condux 08566316

Designed specifically for FTTx applications, the Condux® Microfit Couplers combine ease of use, chemical resistance and ability to accommodate the high pressures encountered when installing fiber with micro-blowing equipment.

STRAIGHT CONNECTOR- 12.7MM MICROFIT COUPLER Condux 08566337

Designed specifically for FTTx applications, the Condux® Microfit Couplers combine ease of use, chemical resistance and ability to accommodate the high pressures encountered when installing fiber with micro-blowing equipment.

STRAIGHT CONNECTOR- 14MM MICROFIT COUPLER Condux 08566318

Designed specifically for FTTx applications, the Condux® Microfit Couplers combine ease of use, chemical resistance and ability to accommodate the high pressures encountered when installing fiber with micro-blowing equipment.

STRAIGHT CONNECTOR- 16MM MICROFIT COUPLER Condux 08566319

Designed specifically for FTTx applications, the Condux® Microfit Couplers combine ease of use, chemical resistance and ability to accommodate the high pressures encountered when installing fiber with micro-blowing equipment.

STRAIGHT CONNECTOR- 18MM MICROFIT COUPLER Condux 08566333

Designed specifically for FTTx applications, the Condux® Microfit Couplers combine ease of use, chemical resistance and ability to accommodate the high pressures encountered when installing fiber with micro-blowing equipment.

Dura-line's Split Lock + is manufactured from a glass fiber that is reinforced with nylon resin. These heat and UV stabilized couplers provide an excellent impact strength. Conveniently reusable, making it ideal for temporarily coupling conduits, especially at slack-loop locations, as well as for air-assisted jetting applications. This coupler can be is easily assembled using a 7/16" nut driver.
Size: 2.00"

Sold 1 ea.