3M Scotchlok 4462SN Shield Bond Connectors
3M Scotchlok 4462SN Shield Bond Connectors
This 3M Scotchlok Shield Bond Connector is specifically designed to supply greater pullout strength than the 4462 shield bond connector. The nuts have been deepened, too, making them much easier to hold and tighten.The shield bond connector is also designed for use with coated cables and has superior electrical properties for the protection of data circuits.
Allied Bolt Weaver Bonding Clamp J8300 One Bare Bronze Groove
BRONZE BONDING CLAMP
- Used to bond #6 copper wire to 1/4" or 5/16" strand
- Constructed of high strength copper alloy
- Installation does not require removal of bolt
- Semi tin plated with one bare bronze groove for copper to copper bond and other groove to be used with dissimilar metals
- Installs with standard terminal wrench
AKA Weaver Bonding Clamp.
Aluminum Grounding Lug Terminal 8700
ALUMINUM GROUNDING LUG
- Used to mechanically bond ground wire to equipment.
- One hole on front of connector for attaching ground wire.
- Accepts ground wire ranging from #14 - #4 AWG
- Mounting hole accommodates 1/4" stud.
- Body constructed from high strength Aluminum.
- Set screw is installed with a flat head screwdriver.
B Strand Grounding Clamp "Mailbox Clamp" J7956
This grounding clamp is used to bond the cable sheath to the messenger strand. Clamp body is made with an inside keeper riding on the end of the bolt. 1/2" bolt can be removed to place the clamp over the messenger wire.
Beam Clamp w/ Square Head MSI SI-2181
MSI SI-2181 Beam Clamp w/ Square Head, is used to provide an electrical connection to trailers, mobile homes or other beam structures. The cup point on bolt penetrates through surface paint or oxide for intimate ground to base metal.
Specifications:
- Seperate screws to attach #14 to #6 AWG ground wires
- High strength bronze casting
- UL & CUL Listed
- Bolt Head: Square
- Beam Ground Clamp
Structure Ground Clamp
Bronze Bonding Clamp J8301/ALL2125 UL
The semi-Tin plated Bronze Bonding Clamp assembly consists of two clamp sections and a 5/16 x 7/8-inch bronze hex washer head bolt.
One clamp section is tapped to allow installation with a single wrench.
Copper Ground Rod Blackburn Bonded Steel 10' x 3/4"
A 3/4" X 10' Copper Bonded Steel Ground Rod. All Blackburn ground rods have
a heavy uniform
covering of electrolytic copper bonded to a rigid
steel core.
Copper ions are forced electrically to join with the
steel core, establishing a
corrosion-resistant bond
between the copper and the steel.
Copper Ground Rod Blackburn Bonded Steel 12'
A 3/4" X 12' Copper Bonded Steel Ground Rod. All Blackburn ground rods have
a heavy uniform
covering of electrolytic copper bonded to a rigid
steel core.
Copper ions are forced electrically to join with the
steel core, establishing a
corrosion-resistant bond
between the copper and the steel.
Economy Copper Ground Strap 12" H-2162
- Provides a permanent connection between a copper water pipe or power service mast and a #14 to #10 AWG ground wire.
- Strap is equipped with an integral square nut which has a male engagement projection that works as a guide during assembly. Strap is supplied with a wire washer and hex nut/hex screw.
- Hardware is sized for installation with a standard 3/8" - 7/16" Can Wrench.
- Hardware is manufactured from pure brass.
- Copper Ground Straps are manufactured from dead soft Copper.
- Stock size is 1/2" x .020".
- UL Listed.
12" Economy Copper Ground Strap H-2162
EM-EM6DB Ground Rod Clamp Breakaway ACORN for 5/8" and 1/2" rods
Product Description
Ground Rod Clamps
Cast bronze, accommodates #12—1/0 AWG (unless otherwise noted).
Features
•Two diameters allow for placement before or after the ground rod has been driven. (A peened-over ground rod is passed through the larger opening and secured in the smaller diameter.) •A locking device prevents the bolt from loosening. •Bronze material keeps corrosion to a minimum.
Clamps marked UL listed, and with a ground wire range of #12–1/0 solid or stranded, are listed as suitable for direct burial and the following ground wire combinations:
Single wire - #12–#1/0 AWG Two like wires - #6, #10, #12 AWG Three like wires - #6, #10, #12 AWG
Unlike wire combinations:
Two #2 AWG with one #6 AWG One or two #10 AWG with one #12 AWG One or two #12 AWG with one #10 AWG
GROUND BOND 5/8" H-J1163
H-J1163 Ground/Bond 5/8"
MSI galvanized steel ground/bond clamp - Used to attach ground wires at the nut end of bolts on transmission lines
- Includes two 1˝" long clamp sections and one square nut
- Constructed of high quality steel, hot-dip galvanized
- Ground Wire Diameter 3/16" - 3/8"
GROUND ROD CAP LEMCO H-207
LEMCO GROUND ROD CAP LEMH-207.
Drive ground rods safely with the Lemco Ground Rod Cap. The 2" diameter surface provides a better target for hammer power, reducing personal injuries due to hammer deflection. Increases speed while protecting ground rods against distortion and damage to finish. Solid steel, plated. Wt. 3 lbs.
Ground Rod Clamp J8493 3/4" ACORN NUT
Bronze Ground Rod Clamps, used with copperbonded 3/4" ground rods, provide a low resistance, secure copper-to-copper connection. These heavy-duty clamps develop a high-pressure contact between the rod and the grounding wire and can be easily disconnected when it is desired to measure resistance of the ground.
Ground Rod Driver Lemco H-693 (No Warranty
Sliding hammer type ground rod driver provides maximum operator safety and driving force. This driver works on rods up to 3/4" diameter. Heavy rubber handgrips absorb the shock of high-density substrate materials. Made of steel and finished with a durable powder coat. Wt. 33 lbs. H693, H-693 LEMCO
There is No Warranty on the Ground Rod Driver Lemco H-693 as this is a hammer tool and it may wear out quickly depending on the soil conditions.
Ground Rod Pounder
Grounding Clamp Hubbell GC5006SH
Grounding Clamp, Copper Cable to Cable, Vice Type. 6 Gage & 6-14 Gage conductors
For copper connections-Splice, Loop deadend or service entrance
tap or grounding connections
• One piece design for easier, faster installation
• Bolt head design for use with standard ratchet wrench
• Vise design achieves high connector pressure with low wrench force
H-J27276 5/8 GROUND CLAMP
H-J27276 5/8 GROUND CLAMP
Features:
MacLean galvanized steel bond clamps provide a sturdy and efficient provision to connect ground wire to threaded bolts. The clamps are designed to nest over the square nut of the bolt. The grounding connection is accomplished by inserting the ground wire between the nut and the bonding clamp and adding an additional nut to secure the clamp and ground connection. The clamps accommodate the most common range of ground wire diameters
List Price: $1.09
Our Price: $1.09
SALE Price: $0.84
You save $0.25!
H-J27277 3/4 GROUND CLAMP
H-J27277 3/4 GROUND CLAMP
Features:
MacLean galvanized steel bond clamps provide a sturdy and efficient provision to connect ground wire to threaded bolts. The clamps are designed to nest over the square nut of the bolt. The grounding connection is accomplished by inserting the ground wire between the nut and the bonding clamp and adding an additional nut to secure the clamp and ground connection. The clamps accommodate the most common range of ground wire diameters
List Price: $1.27
Our Price: $1.27
SALE Price: $0.99
You save $0.28!
MSI H-BVC-6 Bronze Vise Connector 1/4"
MSI H-BVC-6 Bronze Vise Connector
- Interlocking components ensure a
long term, vibration proof connection, one Piece, side opening design
eliminates loose parts, cross
threading, and eases installation on
run conductor
- Easy to install with gloves or hot sticks
- Connectors can be installed on
structures, cabinets and enclosures
- Conductor Range AWG: Max. #6 STR Min. #10 SOL
- Bolt Thread Size: 1/4"
- Bolt Hex. Size: 3/8"
Screw Ground Rod 6' Hubbell G3370
Screw Ground Rod provides a temporary ground where a system ground is not available. When installed, the 6' spiraled ground rod develops less resistance than straight ground rods. Actual effectiveness depends upon soil properties. The reusable Ground Rod is copper clad. The helix (spiral), handle and wing nut are bronze.
Split Bolt S-2 Copper H-852/SI 2002
- Larger Split Bolt
- Used to make a bonding connection between two copper ground wires.
- Bolt and nut formed from high-strength corrosion resistant C210 Copper.
- Specially designed pressure bar provides high pull-out strength.
- Under torque, provides high contact pressure between ground wires.
- Smallest two conductors accepted: 6 Sol.
- Largest two conductors accepted: 2 Str.
- Min. wire size that can be used with Max. wire size: 14 Str.
- Tested and UL listed to UL486A requirements.
Split Bolt S-4 Copper H-853/SI 2004
- Used to make a bonding connection between two copper ground wires.
- Bolt and nut formed from high-strength corrosion resistant C210 Copper.
- Specially designed pressure bar provides high pull-out strength.
- Under torque, provides high contact pressure between ground wires.
- Smallest two conductors accepted: 8 Sol.
- Largest two conductors accepted: 4 Sol.
- Min. wire size that can be used with Max. wire size: 16 Sol.
- Tested and UL listed to UL486A requirements.
List Price: $1.86
Our Price: $1.86
SALE Price: $1.44
You save $0.42!
Split Bolt S-6 Copper H-854/SI 2006
H-854 /SI-2006 SPLIT BOLT
Allied Bolt Part #
854
- Used to make a bonding connection between two copper ground wires.
- Bolt and nut formed from high-strength corrosion resistant C210 Copper.
- Specially designed pressure bar provides high pull-out strength.
- Under torque, provides high contact pressure between ground wires.
- Smallest two conductors accepted: 10 Sol.
- Largest two conductors accepted: 6 Sol.
- Min. wire size that can be used with Max. wire size: 16 Sol.
- Tested and UL listed to UL486A requirements.
List Price: $0.81
Our Price: $0.81
SALE Price: $0.63
You save $0.18!
Strand Tap Clamp 7/16" H-438ALC
- Used to make an electrical connection between ground wire and messenger or guy strands
- Up to 2/0 AWG ground wire
- Up to 7/16" strand size
- Constructed of aluminum
7/16" Strand Tap Clamp H-438ALC
List Price: $5.77
Our Price: $5.99
SALE Price: $4.88
You save $0.89!
Tiiger Ground Rod 3/4 Driver JAMESON RD0034
The Tiiger ground rod driver eliminates the need to climb above the rod for installation.
Designed with a positioning guide pin which allows the driver socket of the impact tool to
be engaged to the ground rod driver.
Tiiger Ground Rod 5/8 Driver JAMESON RD0058
The Tiiger ground rod driver eliminates the need to climb above the rod for installation. Designed with a positioning guide pin which allows the driver socket of the impact tool to be engaged to the ground rod driver.
VISE TYPE BONDING CONNECTOR HUB GC-164 BRONZE
For connecting ribbon or braid to ribbon, braid or bus.
Side Opening Jaw facilitates easy installation.
Run Conductor Size and Type | Cu ribbon 1/4", Cu braid 1/4" |
Tap Conductor Size and Type | Cu 6 sol, Cu 6 str (7), Cu ribbon 1/4", Cu braid 1/4" |
Our Price: $4.61
SALE Price: $3.65
You save $0.96!
Vise Type C Clamp Connector Bolt H-BVC-167P
Designed specifically for connecting a ground wire to a figure 8 messenger strand, where self-supporting cable is used
accommodates messenger diameters of .146" to .312".
Constructed of tin-plated bronze
5/16 - 24 bolt size, 9/16" hex
Messenger Grounding Connector
C Ground Connector accommodates ground conductors
ranging from #8 STR AWG to #4 STR AWG.
List Price: $4.66
Our Price: $4.66
SALE Price: $3.84
You save $0.82!
Vise Type Clamp Connectors EM-2370 Bronze
Silicon bronze clamps adjustable by single hex head screws, used to connect various size grounding conductors, as well as pole line apparatus to grounding conductors.
Features.Casting and bolt are both made of silicon bronze for greater strength, conductivity, and corrosion resistance. Install using the standard can wrench.
EM 2370
Manufactured to Bell Spec CA08980 (H1). It accommodates:
•Single or multiple #6 AWG wires solid or stranded.
•#6 AWG to #10 or #12 AWG.
•From single 2-pair BSW metallic shield, to three 2-pair BSW metallic shields.
Vise Type Clamp Connectors EM-2372/S Bronze
Silicon bronze clamps adjustable by single hex head screws, used to connect various size grounding conductors, as well as pole line apparatus to grounding conductors.
Features.Casting and bolt are both made of silicon bronze for greater strength, conductivity, and corrosion resistance. Install using the standard can wrench.
H2 silicon bronze clamp.
Accommodates:
•#12–#4 AWG solid.
•1/0 B, C, or D stranded copper to #6, #8, #10, #12 AWG solid bare copper wire.
•6.6–10M support strand to #6, #8, #10, #12 AWG solid bare copper wire.
Add suffix -T for a tin-plated clamp.
Vise Type Clamp Connectors H-BVC-167P/EM0167/S
Silicon bronze clamps adjustable by single hex head screws, used to connect various size grounding conductors, as well as pole line apparatus to grounding conductors.
Features.Casting and bolt are both made of silicon bronze for greater strength, conductivity, and corrosion resistance. Install using the standard can wrench.
EM 0167
Tin-plated bronze C connector with teeth for piercing the messenger insulation of Figure 8 cable. For messenger diameters of .146"–.312" (3.71–7.94mm) and ground conductor range of .146"–.312". Available with stainless steel or bronze bolt.