JONARD ASW-716 - ANGLED HEAD SPEED WRENCH 7/16

Speed Wrench Double-Ended measures 7/16" at both ends. Speed head makes tightening and loosening quick and easy, plus head is angled (15°) to ease access. Chrome plated, polished to a high gloss finish, and made of Chrome Vanadium steel. Patented.

JONARD TWAF-71620 - TORQUE WRENCH, FULL HEAD 7/16", 20 IN/LB

Torque Wrench Full Head is a full size open end wrench that behaves like a traditional open end wrench. Designed for "F" Connectors, these wrenches help prevent over tightening. An audible click tells you the connection has been properly achieved.

JONARD TWAF-71630 - TORQUE WRENCH, FULL HEAD 7/16", 30 IN/LB

Torque Wrench Full Head is a full size open end wrench that behaves like a traditional open end wrench. Designed for "F" Connectors, these wrenches help prevent over tightening. An audible click tells you the connection has been properly achieved.

These wrenches all have angle heads, sized for 7/16" F connectors and are designed with an ergonomic cushioned handle for user comfort and protection. These wrenches work in tightening mode only. Torque wrenches are configured for 30 in./lb. (3.39 in Newton Meters) covering most manufacturers' recommended torque requirements for their F connectors.

JONARD TWAF-71640 - TORQUE WRENCH, FULL HEAD 7/16" 40 IN/LB

Torque Wrench Full Head is a full size open end wrench that behaves like a traditional open end wrench. Designed for "F" Connectors, these wrenches help prevent over tightening. An audible click tells you the connection has been properly achieved.

These wrenches all have angle heads, sized for 7/16" F connectors and are designed with an ergonomic cushioned handle for user comfort and protection. These wrenches work in tightening mode only. Torque wrenches are configured for 40 in./lb. (4.52 in Newton Meters) covering most manufacturers' recommended torque requirements for their F connectors. The 40 in./lb. (4.52 in Newton Meters) torque wrench can also be used on bonding hardware.

JONARD TWAFST-71630 - TORQUE WRENCH W/ SST 7/16", 30 IN/LB

Torque wrench is set at 30 in./lb. with security shield attached. Security shield measures 4 ¾" (120mm), is permanently attached and pivots in 90 degree increments. Ideal for hard to reach shielded F connector fittings where a pre-set torque is required.

JONARD TWAS-71620 - TORQUE WRENCH, SPEED HEAD, 7/16", 20 IN/LB

Torque Wrench Speed Head is designed to act like a ratcheting wrench. The tool skips over the corners of the bolt or nut being turned so no repositioning of the tool is required (allowing continuous turning).

Designed for "F" Connectors, these wrenches help prevent over tightening. An audible click tells you the connection has been properly achieved. These wrenches all have angle heads, sized for 7/16" F connectors and are designed with an ergonomic cushioned handle for user comfort and protection. These wrenches work in tightening mode only. Torque wrenches are configured for 20 in./lb. (2.26 in Newton Meters) covering most manufacturers' recommended torque requirements for their F connectors. Torque wrench is 6 1/2" long.

JONARD TWAS-71630 - TORQUE WRENCH, SPEED HEAD, 7/16", 30 IN/LB

Torque Wrench Speed Head is designed to act like a ratcheting wrench. The tool skips over the corners of the bolt or nut being turned so no repositioning of the tool is required (allowing continuous turning).

Designed for "F" Connectors, these wrenches help prevent over tightening. An audible click tells you the connection has been properly achieved. These wrenches all have angle heads, sized for 7/16" F connectors and are designed with an ergonomic cushioned handle for user comfort and protection. These wrenches work in tightening mode only.. Torque wrenches are configured for 30 in./lb. (3.39 in Newton Meters) covering most manufacturers' recommended torque requirements for their F connectors.

JONARD AW-10 - ADJUSTABLE WRENCH 10" with Extra Wide Jaws

Wrench is made of chrome vanadium steel with a chrome plated finish. Wrenches are forged and heat treated for greater strength. Handles are covered with a red transparent plastic for user comfort. The knurl is precision formed and the operation is smooth and trouble free. For accurate and faster adjustments use the metric or English scales on either side of the jaws. With extra wide jaws, a smaller wrench works on bigger jobs. Great for tight spaces.

JONARD AW-12 - ADJUSTABLE WRENCH 12" with Extra Wide Jaws

Wrench is made of chrome vanadium steel with a chrome plated finish. Wrenches are forged and heat treated for greater strength. Handles are covered with a red transparent plastic for user comfort. The knurl is precision formed and the operation is smooth and trouble free. For accurate and faster adjustments use the metric or English scales on either side of the jaws. With extra wide jaws, a smaller wrench works on bigger jobs. Great for tight spaces

JONARD BW-516 - T HANDLE SECURITY WRENCH 5/16"

Tamper proof wrench for use on tamper-proof cross-connect cabinets, MESA and CATV closures. Recessed at both ends, 1/4" deep. Red plastic handle for user comfort.

JONARD BW-532 - BOOTH WRENCH 6" LONG SHAFT

Tamper proof hex screwdriver, also known as a booth wrench or security wrench. It features a 1" diameter screwdriver handle, 5/32" hex shaft with a hole drilled in the tip for use with security tamper proof screws used for telephone and CATV applications.

JONARD BW-532-3 - BOOTH WRENCH 3" LONG SHAFT

Tamper proof hex screwdriver, also known as a booth wrench or security wrench. It features a 1" diameter screwdriver handle, 5/32" hex shaft with a hole drilled in the tip for use with security tamper proof screws used for telephone and CATV applications. Hole Depth 0.25 inches. Hole Diameter 0.094 inches

JONARD JIC-650 - LINEMAN BELL WRENCH

Lineman's B Wrench - JIC-650. Forged and heat treated, this Lineman's Wrench is used on pole line hardware. It is open-end double end type with two sizes of openings at each end and an oval hole for turning pole steps. The end openings accommodate nuts for 3/8", 1/2", 5/8" and 3/4" bolts and the head of the 1/2" drive screw. The faces of the Lineman's Wrench openings are offset to provide handle clearance. 13" Long.

JONARD M-216CKIT - CAN WRENCH SECURITY KEY KIT

Can Wrench with Wire Stripper & Security Key Insert Kit. Six tools in one. Multiple opening, tightening, stripping and security key functions.

CAN WRENCH - M-216CS22, open telephone box fasteners and tighten nuts on binding posts. Designed for universal access to telephone boxes and pedestals. Built in wire stripper with two slots, one for the outside jacket of a four wire "quad" and the other for 22 AWG wire. Black oxide finished 7/16" socket, zinc plated 3/8" socket, thin wall design for tight access and 1 1/4" socket depth.

SECURITY KEY INSERT - SK-51632, designed with a double-ended hex adapter for two sizes of pin-in-head security fasteners. Simply slip the key into the 3/8" side of a can wrench and you are ready for either a 5/16" or 5/32" hex security screw. This is a reversible insert tool. One end is for SLC Cabinets and the other is for most network interface boxes

JONARD M-216CS22 - CAN WRENCH, ERGONOMIC W/ WIRE STRIPPER

Can Wrench Ergonomic 7/8" Diameter Handle, Hex Outer Socket (1 1/2" deep) with 22 AWG Stripper Blade. Open telephone box fasteners and tighten nuts on binding posts. Designed for universal access to telephone boxes and pedestals. Built in wire stripper with two slots, one for the outside jacket of a four wire "quad" and the other for 22 AWG wire. Black oxide finished 7/16" socket, zinc plated 3/8" socket, thin wall design for tight access and 1 1/4" socket depth.

JONARD M-216C/EX - CAN WRENCH, ERGONOMIC HEX

Can Wrench Ergonomic 7/8" Diameter Handle, Hex Outer Socket. Double end can socket wrench, 3/8" and 7/16" hex, orange Impact resistant thermoplastic ergonomic handle. Used in placing fuses in cable terminals and connecting wires to fuses and binding posts. The walls on both sockets are thin enough so they can be used to work locking devices on most terminals and cabinets. 7" long.

JONARD CW-716 - COMBINATION WRENCH 7/16"

Measures 7/16" at both the open end and box end. Both ends have an angle offset (15°) to ease access in confined areas. The box end offers 12 points of contact. Chrome plated, polished to a high gloss finish and made of chrome vanadium steel.

JONARD CWRR-716 - COMBO WRENCH, RATCHETING, REVERSIBLE 7/16"

This combination, ratcheting, reversible wrench measures 7/16” at both ends. A standard open end wrench (with a 15° offset) on one side and a ratcheting reversible box end (with a 15° angled head) on the other. The ratcheting end allows you to toggle from tightening to loosening. It provides 12 points of contact, making this the perfect wrench for cable and satellite installers working on “F” connectors, splitters, wall outlets and on the back of TV’s. Made of chrome vanadium steel, chrome plated and polished to a high gloss finish.

JONARD TTCG-6270-5 - LOCKING TERMINATOR TOOL 5"

A Cam Style locking terminator tool for Corning Gilbert style terminators. Works on Gilbert NS-5762-3 (plus -9, -11, -13 & -15 terminators). High quality aluminum construction, blue color.

JONARD TTCG-6270-9 - LOCKING TERMINATOR TOOL 9"

A Cam Style locking terminator tool for Corning Gilbert style terminators. Works on Gilbert NS-5762-3 (plus -9, -11, -13 & -15 terminators). High quality aluminum construction, blue color.

JONARD TT-4 - TERMINATOR TOOL 4"

Terminator Tool 2 ½" shaft, overall length 4 ½". Tool is used for various locking terminators. Use for the Gilbert Engineering GTP (Morlock), PRC (Production Products Company), LFT, PCT (International Technology), TPG, TR 75 GTL (Viewsonics), SV-LT & SV-LTA (Signal Vision) locking terminators, and pedestal locks NO-3-Pedlock, NO-4-Pedlock. Ergonomic handle provides greater leverage and a superior grip.

JONARD TT-7 - TERMINATOR TOOL 7"

Terminator Tool 4” shaft, overall length 8". Tool is used for various locking terminators. Use for the Gilbert Engineering GTP (Morlock), PRC (Production Products Company), LFT, PCT (International Technology), TPG, TR 75 GTL (Viewsonics), SV-LT & SV-LTA (Signal Vision) locking terminators, and pedestal locks NO-3-Pedlock, NO-4-Pedlock. Ergonomic handle provides greater leverage and a superior grip

JONARD TT-7V - TERMINATOR TOOL WITH PRONGS

Pronged Terminator Tool 4” shaft, overall length 9". Tool is used for various locking terminators. Use for the Gilbert Engineering GTP (Morlock), PRC (Production Products Company), LFT, PCT (International Technology), TPG, TR 75 GTL (Viewsonics), SV-LT & SV-LTA (Signal Vision) locking terminators, and pedestal locks NO-3-Pedlock, NO-4-Pedlock. Ergonomic handle provides greater leverage and a superior grip.