The Slingco Deluxe Pole Puller system includes the pole puller pad and back plate weldment. The pole puller pad has studs which keep the base plate in the optimum position when pulling poles. The back plate weldment has angled teeth to increase hold on the pole during extraction.

Slingco’s pole puller offers a low point of attachment making it easy to remove even broken or cut poles.

• Low point of attachment
• 50,120 lbs lift at max pressure
• Deluxe System complete with back plate weldment & pad

Hydraulic Pole Puller

TiiGER 4001D hydraulic pole puller. Remove wood poles and metal poles safely and efficiently with the TiiGER® Hydraulic Pole Puller. At 57 pounds, our Pole Puller is the lightest and safest on the market. Utilizing a swivel and back plate, a chain provides maximum grip as the hydraulic cylinder removes the pole. The low attachment point allows chain and back plate to grip cut poles up to 14” from the ground. To minimize tip-ping, base plate has the lowest possible center of gravity. The TiiGER 4001D Pole Puller can be disassembled for easy transport and storage

(Hoses and Fittings must be ordered separately)
Female Quick Connect hydraulic fitting HST 800801002
Male Quick Connect hydraulic fitting HST 800801003
Manta Ray HC-16-25 Hydraulic Hose 25' with HTMA-3A Coupler (Two Hoses Required)

COMPONENT PART NUMBERS (SOLD SEPARATELY)

• Base Plate HA008
• Swivel & Hook Assembly HA0016

Back Plate Standard 4040B
Pole Puller Pad HA0040

The toughest manhole covers are easy to move with this one piece lifter. It features ....

Cable Capacity: 2 (.750) produces 36” overall length loop. Easy-grip pawl ensures positive engagement into gear rack....

Cable Capacity: 2 (.750) produces 36” overall length loop. Easy-grip pawl ensures positive engagement into gear rack....

Cable Capacity: 2 (.750) produces 36” overall length loop. Easy-grip pawl ensures positive engagement into gear rack....

Cable Capacity: 2 (.750) produces 36” overall length loop. Easy-grip pawl ensures positive engagement into gear rack....

Comes with Li-ion battery pack/ charger/ AC and DC adapters. Also come with 3' hose and probe..Built around high-quality micro-sensor technology, the GX-2012 is RKI’s smallest personal 5 sensor gas monitor with a built in sample pump. Weighing only 12.3 ounces, two operating modes: Normal (for confined spaces) and Bar Hole.

SLINGCO crimping tools have been designed to provide reliable crimps installing full-tension or non-tension connectors. Mechanical Crimping Tools also have ergonomic handles for comfortable use and maximum leverage when making critical connections.

The Hastings shotgun hot stick that has an external operating rod. This style of clampstick puts an easy to control hook on the end of an insulated hot stick designed for installing hot-line and grounding clamps.
Hasting 8104, Hasting 8106 & Hasting 8108

The “No Twist” stick has a unique triangular design. All models are heavy duty. Triangle shape enables each section to “lock in automatically”, no need to search for the button.

Measures pole heights and conductor clearances from the ground. Universal end fitting on the insulated top section accepts a wide variety of attachments so that the lineman can disconnect switches, replace cut out tubes and reclose, remove pole covers, prune trees, etc., with one tool.

The Jonard CableSaber™ is the ultimate tool for gaining mid-span access to armored or thick jacketed cables 4 mm-28.6 mm (0.157”-1.125”) in diameter.

With preset factory settings and no adjustments required, this fiber optic stripper is designed to strip 250μm buffer coating to expose the 125μm optical fiber in fiber optic cables.

Compact, lightweight wire-stripping and cutting tool. Narrow nose fits into tight places. Hardened steel with...

Klein wire stripper6-12 AWG, Precision shear-type blades for clean cuts on stranded copper wire....

.

Klein's precision flush cutter shears soft wire up to 18 AWG producing a flat, straight cut. The ultra slim profile makes it easier to get into tight spaces. Cushioned grips and steel spring return help reduce fatigue when making repetitive cuts. The blades are heat treated for long life. This is your go-to tool when you want precision and control when cutting soft wire.

Voltage Tester designed specifically for HVAC applications. Volt Pen provides non-contact determination of AC voltage in cables, cords, circuit breakers, switches, outlets and wires, as well as AC voltage in security, entertainment, communications, environmental control, and irrigation systems.

One-step outer jacket stripping of category 3, 5, 5e, 6, and 6a cables. Durable high-carbon steel cutting blades are ground and honed for long life. Removes the outer jacket of twisted-pair cable without damaging the conductors. Strip and slit lengths may be varied to accommodate different connector requirements. Recessed cutting surface slits long runs of twisted-pair cable.

The Punchdown Multi-Tool with 110/66 blade terminates and cuts wire in one convenient step. It is spring-loaded for fast low effort seating and terminating. The included precision ground combination 66 and 110 blade and the variety of optional WorkEnds™ driver bits provide flexibility. The cut side is color coded yellow for identification.

Measures pole heights and conductor clearances from the ground. Universal end fitting on the insulated top section accepts a wide variety of attachments so that the lineman can disconnect switches, replace cut out tubes and reclose, remove pole covers, prune trees, etc., with one tool.

Our M12™ Plastic Pipe Shear Kit with the powerful M12™ 12-Volt Lithium-Ion battery included can slice through 2 inch schedule 80 PVC in just 3 seconds. The pipe shear kit is compatible with M12™ lithium-ion batteries, giving you more than 200 cuts on a single charge. The stainless steel blade and aluminum jaw are impact and water and rust resistant.

MILWAUKEE® M18 FUEL™ 7/16” Quick-Release Hex Utility High Torque Impact Wrench w/ ONE-KEY KIT™ delivers the Fastest Drilling Speed, More Power, and is Built for Maximum Control. The POWERSTATE™ Brushless Motor and all-new mechanism provide linemen with 30% faster drilling speeds, increasing your productivity while on the job.

Replaces M12™, M18™, V28®, and 9.6V - 28V Incandescent Bulbs - LED replacement for most work lights. 3X Run-Time - Increased efficiency for all work lights, 50,000-Hr. LED - Lasts over 250X longer than 18V incandescent bulb, Impact Resistant - Solid state light element does not fail when dropped. Compatible with Milwaukee® M12™, M18™, V28®, and most other major power tool work lights.

REL R-3/4GS RATCHETING EHS GUY CUTTER
3/4" Capacity, shear-cut blade holds material in place.
Cuts:

• EHS guy strand
• Wire rope
• Aircraft cable
• Hard SS cable

REL R-GS RATCHETING GUY STRAND CUTTER
7/16" Capacity, notched blades hold material, while ratchet produces easy, progressive cuts.
Cuts:

• EHS guy strand
• Mild steel rods,
• Bolts and similar materials

Replacement Head for REL R-3/4GS RATCHETING EHS GUY CUTTER 3/4"

Replacement Head available for easy end quick repair 3/4" Capacity, shear-cut blade holds material in place.

REPLACEMENT HEAD FOR REL R-GS RATCHETING GUY STRAND CUTTER 7/16"

Compact design for precise, longitudinal fiber stripping.

• Compact, lightweight & ergonomic tool with center feed design provides precise, longitudinal fiber stripping from the 900 micron buffer coating down to the 125 micron bare fiber
• Convenient, side-mounted stripper blades remove the 1.6 to 3 mm jackets
• All cutting surfaces are precision-formed, hardened, tempered & ground to ensure accurate fiber stripping without damaging the fiber
• Factory-set & no adjustment necessary
• Patent-pending

Screw Ground Rod provides a temporary ground where a system ground is not available. When installed, the 6' spiraled ground rod develops less resistance than straight ground rods. Actual effectiveness depends upon soil properties. The reusable Ground Rod is copper clad. The helix (spiral), handle and wing nut are bronze.

The TBM5-S comes with five multi-nested color-coded die sets, which mount directly on the tool for storage and whose codes are automatically embossed on the crimped connector. Features Shure-Stake ratchet.
Thomas and Betts makes the TBM5S color-keyed mechanical compression tool for C-Taps, Copper and Aluminum connectors.

• Wide range of #8 AWG to 250 kcmil for copper and # 10 to 4/0 AWG for aluminum lugs and splices
• Also installs C-taps from 54705 to 54705
• Shure-Stake Mechanism ensure a property complete crimping each time
• Includes color-code-embossed installation dies

Applications.

• I deal for pigtailing, Two-way splicing or tapping to an unbroken continuous main

• Heavy reinforcing ribs help locate compression dies and strengthen compressed joint

• Dims: L 1-5/32, H 27/32, E 9/32

• Color Key: Pink

*USE WITH TIIGER POLE PULLER*
Tiiger’s 4041B Long Tooth Back Plate has 1-1/2″ long teeth. Designed for use with Tiiger’s Pole Puller Assembly.

Plate Makes It Easy to Stop Chain Slippage On Hard, Small-Diameter, or Greasy Poles. Long Tooth Plate For Poles With Severe Shell Rot Only

The Bashlin 336A traveling ground reduces the possibility of electric shock due to accidental contact with energized conductors during stringing operations. They are heavy duty units designed for conductors Up to 336MCM (5/8")