The Split Lock + is a split coupler produced from a glass fiber reinforced nylon resin. The coupler is heat and UV stabilized, and offers excellent impact strength. It’s reusable and is ideal for temporarily coupling conduits, particularly at slack-loop locations, and also for air-assisted jetting applications. The coupler is easily assembled using a 7/16” nut driver.
Size: 1.25"
Features:
• No special tools required
• Reusable – can install with cable inside
• Heat, UV stabilized
• Fungus and chemical resistant
• Air and water tight
• No I.D. reduction
• Not recommended for plow chute
• Meets UL 514B pullout requirements
• ETL listed to UL STD 514B and CSA STD C22.2 18.3

The Split Lock + is a split coupler produced from a glass fiber reinforced nylon resin. The coupler is heat and UV stabilized, and offers excellent impact strength. It’s reusable and is ideal for temporarily coupling conduits, particularly at slack-loop locations, and also for air-assisted jetting applications. The coupler is easily assembled using a 7/16” nut driver.
Size: 1.00"
Features:
• No special tools required
• Reusable – can install with cable inside
• Heat, UV stabilized
• Fungus and chemical resistant
• Air and water tight
• No I.D. reduction
• Not recommended for plow chute
• Meets UL 514B pullout requirements
• ETL listed to UL STD 514B and CSA STD C22.2 18.3

The Split Lock + is a split coupler produced from a glass fiber reinforced nylon resin.The coupler is heat and UV stabilized, and offers excellent impact strength.It’s reusable and is ideal for temporarily coupling conduits, particularly at slack-loop locations, and also for air-assisted jetting applications.The coupler is easily assembled using a 7/16” nut driver.
Size: 1.50"
Features:
• No special tools required
• Reusable – can install with cable inside
• Heat, UV stabilized
• Fungus and chemical resistant
• Air and water tight
• No I.D. reduction
• Not recommended for plow chute
• Meets UL 514B pullout requirements
• ETL listed to UL STD 514B and CSA STD C22.2 18.3

Duraline 20001491, no heat or tools are needed. Simply push the duct ends into the coupler for a locked and air-sealed assembly.The compact profile of the PUSH-LOCK is well suited for use in pull boxes, vaults, or other limited-access areas such as narrow trenches. The non-metallic construction provides excellent corrosion resistance in buried or encased applications and also has desirable dielectric properties. The PUSH-LOCK is non-transparent and contains UV inhibitors, but is not recommend for aerial applications.
Size: 3/4"(27mm)

GMP 70726, clear bodied push-on connector (coupler) is a no-tool connector that make it fast and easy to join two lengths of microducts of the same size.
Size: 0.63" (16mm)
*Pack of 25*

CALAM 2250-015 Polly-Pull Tampered Temporary Conduit Plug in color, has LPDE construction for added durability. The plug with ribbed sidewalls, provides tight seal. It features extended base-lip for easy removal. It is suitable for interim sealing of standard duct, bell-ends and terminators thus ensuring damage protection.
Specification:

• Color: Black
• Trade Size: 1-1/2"
• Dimensions: 1.87" Dia. X 2.59" length

Condux 08041520 Aluminum Split Bells 2"
Condux Aluminum Split Bells plugs into conduit in manhole wall, guiding cable safely into the conduit
regardless of pulling angle.
Specification:

• Size: 2" (51 mm)
• Tube Length: 8" (203 mm)
• Tube I.D. : 1.63" (41 mm)
• Tube O.D. : 1.88" (48 mm)

Condux 08041530 Aluminum Split Bells 3"
Condux Aluminum Split Bells plugs into conduit in manhole wall, guiding cable safely into the conduit
regardless of pulling angle.
Specification:

• Size: 3" (76 mm)
• Tube Length: 8" (203 mm)
• Tube I.D. : 1.63" (41 mm)
• Tube O.D. : 2.88" (73 mm)

Condux 08041535 Aluminum Split Bells 3.5"
Condux Aluminum Split Bells plugs into conduit in manhole wall, guiding cable safely into the conduit
regardless of pulling angle.
Specification:

• Size: 3.5" (89 mm)
• Tube Length: 8" (203 mm)
• Tube I.D. : 3.13" (79 mm)
• Tube O.D. : 3.38" (88 mm)

Condux 08041540 Aluminum Split Bells 4"
Condux Aluminum Split Bells plugs into conduit in manhole wall, guiding cable safely into the conduit
regardless of pulling angle.
Specification:

• Size: 4" (102 mm)
• Tube Length: 8" (203 mm)
• Tube I.D. : 3.63" (92 mm)
• Tube O.D. : 3.88" (98 mm)

Condux 08041550 Aluminum Split Bells 5"
Condux Aluminum Split Bells plugs into conduit in manhole wall, guiding cable safely into the conduit
regardless of pulling angle.
Specification:

• Size: 5" (127 mm)
• Tube Length: 8" (203 mm)
• Tube I.D. : 4.63" (117 mm)
• Tube O.D. : 4.88" (124 mm)

Condux 08041564 Aluminum Split Bell
Condux Aluminum Split Bell plugs into conduit in manhole wall, guiding cable safely into the conduit
regardless of pulling angle.
Specifications:
Size: 6" (152 mm)
Tube Length: 12" (304 mm)
Tube ID: 5.63" (143 mm)
Tube OD: 5.88" (149 mm)

FREE 2019 CALENDAR

White Lightning WL099110C Contractor RTV Silicone Sealant Clear 3m
ONE 10 OUNCE TUBE.
Contractor RTV Silicone Sealant is an interior/exterior sealant that seals out moisture, air, dust, dirt and noise. Contractor RTV Silicone is easy to use, non-slumping and requires no mixing. It adheres to a wide range of common building materials.

Checker Steel Cover for B1017 Concrete Box

B3048-53JH, bolt down 3 piece steel checkered plate cover.

B24"x36"-52JH, 2 piece steel checkered plate cover, bolt down.

B2436, 24 x 36 x 12" steel frame concrete Utility Box.

B1730X12, 12" reinforced concrete extension
for B1730 ulility box.

B1730-51JH, steel checker plate cover, bolt down.

B1730, 17" x 30" concrete utility box.
BOX ONLY

Concrete Vault Extension 24x36x12"

Concrete with steel frame utility Vault.
Concrete Traffic Vault 30"x48"x12" BOX

A steel checker plate cover, bolt down, for the B1324 utility box.

13"X24X12 concrete utility vault.

Concrete Traffic Vault 10x17x12" BOX

Concrete Vault Extension 30X48X12"

Vault Extensions 10x17x12" EXT
concrete

CONCRETE Vault Extensions 13x24x12" EXT

SPLIT PLASTIC COUPLER 2" CABTEC-PE2.375-2
The couplings are removable and lightweight, sealing completely to 200 lbs PSI and are guaranteed to handle tensile loads up to 600 lbs.
Reusable.

SPLIT PLASTIC COUPLER 1'' CABTEC-PE1.315-2
The couplings are removable and lightweight, sealing completely to 200 lbs PSI and are guaranteed to handle tensile loads up to 600 lbs.
Reusable.

SPLIT PLASTIC COUPLER 1.5" CABTEC-PE1.900-2
The couplings are removable and lightweight, sealing completely to 200 lbs PSI and are guaranteed to handle tensile loads up to 600 lbs.
Reusable.

SPLIT PLASTIC COUPLER 1.25'' 2PC CABTEC-PE1.660-2
The couplings are removable and lightweight, sealing completely to 200 lbs PSI and are guaranteed to handle tensile loads up to 600 lbs.
Reusable.

Cable-Tec ASB1.488 TRUESIDR11.5 Airtight Aluminum Coupling, Reversed Thread Barbed
This series of aluminum airtight couplings incorporates the same reliable, full circumference seal used in our barbed ring compression couplings. But unlike other one piece plastic or aluminum compression couplings that have to be installed with some type coupling press, These reverse threaded barbed ring couplings can be installed like any ordinary reverse thread coupling. Instead of a coupling press, a special wide pitch, fast traveling thread is used to force the innnerduct over barbed ring seal. Sold individually.
SDR Duct Outer Diameter: 1.488

O.D 1.194 This series of aluminum airtight couplings incorporates the same reliable,

full circumference seal used in our barbed ring compression couplings.

But unlike other one piece plastic or aluminum compression couplings

that have to be installed with some type coupling press,

these reverse threaded barbed ring couplings can be installed

like any ordinary reverse thread coupling. Instead of a coupling press,

a special wide pitch, fast traveling thread is used to force the innnerduct

over barbed ring seal. Sold individually.

The Kwikie plug functions by compressing a thermo-plastic elastomer seal between two U.V., ozone and chemically resistant compression plates through the hand-tightening of a loop or wing nut; the compressed seal expanding into full contact with the inside pipe walls thereby providing an effective, permanent, positive seal to your conduit system in seconds.

The Kwikie plug functions by compressing a thermo-plastic elastomer seal between two U.V., ozone and chemically resistant compression plates through the hand-tightening of a loop or wing nut; the compressed seal expanding into full contact with the inside pipe walls thereby providing an effective, permanent, positive seal to your conduit system in seconds.

The Kwikie plug functions by compressing a thermo-plastic elastomer seal between two U.V., ozone and chemically resistant compression plates through the hand-tightening of a loop or wing nut; the compressed seal expanding into full contact with the inside pipe walls thereby providing an effective, permanent, positive seal to your conduit system in seconds.

Poly-Pull Plug is molded from the highest grades of virgin Low Density Polyethylene (LDPE),
a tough, high-impact and chemically inert resin that has near-zero moisture absorption properties.
LDPE is resistant to ultraviolet light, ozone and is capable of withstanding extreme fluctuations in temperature.
While seemingly simple in concept, the Poly-Pull Plug has many design features making it an effective,
efficient and economical means for the sealing of your conduit lines. A long-run tapered design allows for easy
and quick insertion into your empty duct while a concentric set of scalloped ridges on the outside wall of the plug
ensures a tight seal and prevents accidental dislodging of the plug. At the base of the Poly-Pull, is a sturdy,
extended lip that allows a firm grip for easy removal of the plug.

Poly-Pull Plug is molded from the highest grades of virgin Low Density Polyethylene (LDPE),
a tough, high-impact and chemically inert resin that has near-zero moisture absorption properties.
LDPE is resistant to ultraviolet light, ozone and is capable of withstanding extreme fluctuations in temperature.
While seemingly simple in concept, the Poly-Pull Plug has many design features making it an effective,
efficient and economical means for the sealing of your conduit lines. A long-run tapered design allows for easy
and quick insertion into your empty duct while a concentric set of scalloped ridges on the outside wall of the plug
ensures a tight seal and prevents accidental dislodging of the plug. At the base of the Poly-Pull, is a sturdy,
extended lip that allows a firm grip for easy removal of the plug.

The Kwikie plug functions by compressing a thermo-plastic elastomer seal between two U.V., ozone and....

The Kwikie plug functions by compressing a thermo-plastic elastomer seal between two U.V., ozone and....

The Kwikie plug functions by compressing a thermo-plastic elastomer seal between two U.V., ozone and....

The Kwikie plug functions by compressing a thermo-plastic elastomer seal between two U.V., ozone and...

CALAM Kwikie plug functions by compressing a thermo-plastic Elastoplast seal between two U.V., ozone and chemically resistant compression plates through the hand-tightening of a loop or wing nut; the compressed seal expanding into full contact with the inside pipe walls thereby providing an effective, permanent, positive seal to your conduit system in seconds. All Kwikie plugs that are designed for conduit pipe larger than two inches are hollow-stemmed and may be used for feeding or bleeding fluids from your lines (½” hose thread adaptor available). Other options include wing nuts or eye nuts for tightening the compression plates, flush-fit vs. inside-fit (the outside compression plate on flush-fit Kwikies will not enter the conduit) and schedule 40 and schedule 80 sizing. All Kwikie plugs come with a ½” rope tie for sealing and securing excess rope within the conduit system for future use.
Expandable Duct Plug w/ Loop Nut

• Size: 1-1/2"

The Kwikie plug functions by compressing a thermo-plastic elastomer seal between two U.V., ozone and....

The Kwikie plug functions by compressing a thermo-plastic elastomer seal between two U.V., ozone and....

The Kwikie plug functions by compressing a thermo-plastic elastomer seal between two U.V., ozone and....

The original Condu-Grip provides a 100% long-term airtight and watertight seal for smooth wall PE conduit.....

The original Condu-Grip provides a 100% long-term airtight and watertight seal for smooth wall PE conduit....

Pullout Strength 3000LBSThe original Condu-Grip provides a 100% long-term airtight and watertight seal for smooth wall PE conduit. The NR (no 0-ring) model provides a sufficient seal for most cable blowing applications. All models have a very high tensile pullout resistance and the Condu-Grip is completely non-corrodable an all soil conditions and is simple to install with no special tool required. The Condu-Grip can be threaded or pressed on and still provide outstanding performance.
IPS PIPE OD 1.90" FOR 1.5" PIPE/DUCT

The original Condu-Grip provides a 100% long-term airtight and watertight seal for smooth wall PE conduit....

These portable power sources are matched perfectly to the power requirements of the Condux Fiber Optic Cable Puller and....

Split plug with bushing assembly for sealing around cable in duct installations.

Split plug with bushing assembly for sealing around cable in duct installations.