The Ground Hog SD12 Standard Auger has a standard-style digging head for loose/sandy soil condition. This 12" Auger uses a screw-in fishtail centered pilot and bolt-on wide flat, hardfaced, standard side blades. All Ground Hog Augers are approximately
38"(3') in length and utilize a 7/8" standard square drive for interchangeability between Earth Drills.
Feature:

• Part #100 Fishtail Pilot(1)
• Part #912 Side Blade Installed(1)
• Part #1300 Attachment Pin & Clips(1)
• 7//8" Square Drive for interchangeability
• Durable Powder-Coated Finished
• 12" hole diameter

The Ground Hog PSD8 Pengo 8" Auger features heat treated cast alloy steel boring heads with hardened forged steel side blades and a bolt-on cast alloy steel centered pilot bit. The Pengo Series augers are general purpose augers and are the best choice for tough soil conditions. All Ground Hog Augers are approximately 38"(3') in length and utilize a 7/8" standard square drive for interchangeability between Earth Drills.
Features:

• Part # SB-25 Pilot Bit(1)
• Part # 35 Side Blades Installed(2)
• Part # 1300 Attachment Pin & Chip
• 8" hole diameter
• 7//8" Square Drive for interchangeability
• Screw-in hardfaced alloy steel pilot bit
• Durable Powder-Coated Finish
• Replaceable Forged Steel Side Blades

The Manta Ray load locker Manta Ray LL-1 is required to load lock and proof test the anchor.

The Manta Ray load locker Manta Ray LL-1 is required to load lock and proof test the anchor.

The Taper Jaw provides grip to the Adapter Setting Bar which is pulls upwards on the anchor rod tipping the anchor underground.

Manta Ray 50236 SG-3, Radiused Drive Tip 30", this piece is shaped to fit into the anchor on one end and threaded on the other end to accept a coupler.

Manta Ray 50424 SG-X Drive Steel Extractor Bar is used in conjunction with the LL-1 Load Locker to extract any drive steel that happens to get stuck underground.

Manta Ray Replacement (#50254) Force Gauge with Range Marking Sticker and (#50253) Coupler for
Manta LL-1 Load Locker. *REPLACEMENT PART ONLY*

The Ground Hog SD12 Standard Auger has a standard-style digging head for loose/sandy soil condition. This 12" Auger uses a screw-in fishtail centered pilot and bolt-on wide flat, hardfaced, standard side blades. All Ground Hog Augers are approximately
38"(3') in length and utilize a 7/8" standard square drive for interchangeability between Earth Drills.
Feature:

• Part #100 Fishtail Pilot(1)
• Part #912 Side Blade Installed(1)
• Part #1300 Attachment Pin & Clips(1)
• 7//8" Square Drive for interchangeability
• Durable Powder-Coated Finished
• 12" hole diameter

Manta Ray Replacement (#50254) Force Gauge with Range Marking Sticker and (#50253) Coupler for
Manta LL-1 Load Locker. *REPLACEMENT PART ONLY*

The Ground Hog 12-inch auger with Standard style digging head. For loose/sandy soil conditions. Uses a screw-in fishtail center pilot and hardfaced bolt-on Standard style side blade. Comes ready to dig with one Part# 100 Fishtail Pilot and one Part# 912 side blade installed. Includes one Part# 1300 attachment pin and clip.
Features:

• Part # SB-25 Pilot Bit(1)
• Part # 35 Side Blades Installed(2)
• Part # 1300 Attachment Pin & Chip
• 12" hole diameter
• 7//8" Square Drive for interchangeability
• Screw-in hardfaced alloy steel pilot bit
• Durable Powder-Coated Finish
• Replaceable Forged Steel Side Blades

American Pneumatic tool tampers are available with a choice of three types of butts. This is a half moon shaped butt.

American Pneumatic tool tampers are available with a choice of three types of butts. 6" Round Butt internally reinforced.

The APT Model 131 Backfill Tamper is used for soil compaction, temporary filling of holes, ashphalt packing etc.

This lightweight 30 lb class Paving Breaker is an ideal tool for light to medium demolition work, as well as for use in confined areas.

Tough and dependable, the high performance Model 190 Paving Breaker or Jack Hammer is the most powerful tool American Pneumatic Tool makes.

ROCK DRILL M137 Chuck Size 7/8 x 3-1/4", 7/8 x 4-1/4" or 1 x 4-1/4"

The APT Model 137 Rock Drill is a versatile, mid-sized rock drill used in general construction, utility work and plant maintenance.

ROCK DRILL M155 Chuck Size 7/8 x 3-1/4", 7/8 x 4-1/4" or 1 x 4-1/4"

The APT Model 155 Rock Drill is a versatile, mid-sized rock drill used in general construction, utility work and plant maintenance. It is designed for drilling through granite, hard faced rock, quarry drilling and for drilling secondary holes for blasting. It can also be used in conjunction with dowel hole drilling machinery.
The Model 155 is adaptable to wet drilling by attaching the APT valve, wet tube and swivel assembly.
5229 -M155 ROCK DRILL 7/8 X 3-1/4", 5231 -M155 ROCK DRILL 7/8 X 4-1/4", 5233 -M155 ROCK DRILL 1 X 4-1/4"

The open style has advantages in portability, accessibility and cost. On the job, gain easy access to all components with the open face design.

The C-71-5H Earth Drill is the work-horse of the Ground Hog line, tried and tested for over 30 years. Also known as an " Anchor Drill". This is a two man drill. Auger Bits sold separately.

Ground Hog offers a large range of augers and accessories for our earthdrills to cover all types of soil conditions and customer requirements

Ground Hog Pengo Drill 4" x 3'. Ground Hog offers a large range of augers and accessories for our earthdrills to cover all types of soil conditions and customer requirements.

Complete Kit Hydraulic Auger MANTA LB-1 50093

This 42" auger is designed for compacted clays, asphalt, coral rock, soft sandstone and limestone. Includes a 4" carbide blade.

The MANTA LB-9023-C4RT Little Beaver 4" Carbide Blade with Ripper Teeth
Does NOT include tube auger.

Little Beaver Adaptor, with Hardware, Keyed Shft to Auger


Earth Drills

Driving utility anchors is made easier with this special adaptor. With Little Beaver’s anchor handle, hydraulic earth drill and torque tube, one-man installation of utility anchors is now possible. (60 RPM only)

Little Beaver Carbide Blade with Hardware for Snap-On Augers (4")
Does NOT include tube auger.

Spring and Button - Little Beaver 9058

This adaptor adapts Little Beaver earth drills to Groundhog brands of augers. Features a 7/8" square drive connection.

Earth Drills

When deeper holes are required, add a snap-on extension. Each extension is equipped with a spring loaded snap button for a fast, yet secure connection!

Not for any Type of Anchor rods. Twin eye-nuts accommodate double guys. For 5/8-11 hardware. Will not fit D-62 Rod .

Twin Eyenut 5/8" J6515

Not for any Type of Anchor rods. Twin eye-nuts accommodate double guys. For 5/8-11 hardware. Will not fit D-62 Rod .

Twin Eyenut 5/8" J6515

Canvas Bag for the Manta Ray Earth Anchor Drive Set (SGC)

Used Only in conjunction with PISA D100 1" Anchor rods , D10031C 1" x 3-1/2ft or D75 rod for helical and Manta Ray anchors.

5/8" Rod Coupling, Part Number: D352, Used with D-62 5/8" Rod Only.
Power Hub Screw Anchor Rod Couplings are used to couple additional rods together when further installation depths are needed or to extend the eyenut above grade.

3/4" & 1" Rod Coupling, Part Number: D354, Used with D100, D75 & D10031 Rods Only.

Manta Ray  Anchor Tags

Manta Ray Load Locker KIT Metal Box 50250, Use to storage the Manta Ray Locker Kit

*MR1* 7" x 14 1/2" – To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods

The SGC-14 drive steel kit, or a GADD set, will drive and install Manta Ray Anchors.
Designed for 1-1/4" x 6" chuck hammer/breakers

*MR2* 4" x 14 1/2" –To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only.

1-1/8" hex x 6" shank, 15-1/2" OAL

MANTA 50655 SG-4HD HEAVY DUTY COUPLER

1-1/4" hex x 6" shank,

*MR3* Manta Ray Anchor 3.5x11.88 - Use with D62 5/8 Pisa Rod and J6516 5/8 twin eyenut. For 5/8 anchor rods only

To be used with 7ft 1" D100, 3.5ft 1" D10031, or D75 3/4" 12632 Pisa rods only.17.25 x 12.5"

Manta Ray HC-16-25, a 25' (7.6m) Hydraulic Hose with HTMA-3A Flush Face Coupler.

*Two are required for Manta Ray and/or Pole Puller Operations*

Manta Ray 50172 LL-2. Light Duty Hand Pump.The LL-2 Anchor Locking kit is designed to Load Lock and proof test Small Manta Ray and Duckbill anchors.

*MR4* Manta Ray Anchor 3.5x11.88 - Use with D62 5/8 Pisa Rod and J6516 5/8" twin eyenut. For 5/8 anchor rods only.

MOIL POINT 18"UC X 11/4 X 6 BRUNNER & LAY #A44018 DELSTEEL
Stanley Hydraulic Tools Heavy Duty Moil Point 18" ( 45.7 cm ) for Handheld Breakers BR45/BR50/BR67/BR87

CLAY SPADE 1 1/4 X 6 BRUNNER & LAY #B40400 1 1/4" X
Stanley Hydraulic Tools Clay Spade 8" ( 20.3 cm ) for Handheld Breakers BR45/BR50/BR67/BR87

Manta Ray 50127 Hydraulic Control Valve and Plate LL-1. The Manta Ray load locker Manta Ray LL-1 is required to load lock and proof test the anchor.

The Manta 50382 Stanley GT18 hydraulic power unit is engineered for continuous professional use and is optimized to deliver ideal flows and pressures to both type 1 and 2 hydraulic tools.